| About |
|---|
| SABIC® LLDPE RG50035 SABIC® LLDPE RG50035 is a Linear Low Density Polyethylene reactor powder grade typically used for various compounding applications, including Wire & Cable extrusion. SABIC® LLDPE RG50035 contains a low level of antioxidants and does not contain any antiblock and/or slip agents. Application Wire & Cable Extrusion: Base resin for Cable compounds and masterbatches. Masterbatch Compounding: Compounding applications, like colour masterbatches. This product is not intended for and must not be used in any pharmaceutical/medical applications.&&SABIC® LLDPE RG50035 SABIC® LLDPE RG50035 is a Linear Low Density Polyethylene reactor powder grade designed for various compounding applications. SABIC® LLDPE RG50035 contains low level of antioxidant and does not contain any antiblock and/or slip agents. Application Compounding applications, like colour masterbatches. The product mentioned herein is in particular not tested and therefore not validated for use in pharmaceutical/ medical applications.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Linear low density polyethylene |
| Material Status | Commercial: Active |
| Features | Good flexibility,Good thermal shock resistance,Insulation |
| Availabilitys | North America |
| Process Methods | casting |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.935 | g/cm³ | ISO 1183, ASTM D1505 |
| Apparent density | 0.42 | g/cm³ | ASTM D1895 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 5.0 | g/10min | ASTM D1238，ISO 1133 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| Yield, molding | 14.0 | MPa | ISO 527-2 |
| Tensile strain | ISO 527-2 | ||
| Yield, molding | 15 | % | |
| Fracture, molded | 100 | % | |
| Bending modulus | |||
| 23 ℃, molded | 490 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| Compression Molding | 40 | kJ/m² | ISO 180-A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 114 | ℃ | ISO 306/A |
| Melting temperature | |||
| DSC | 125 | ℃ | Internal Method |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 7.0E+15 | ohms·cm | ASTM D257 |
| Dielectric strength | 61 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 60 Hz | 2.19 | ASTM D150 | |
| Dissipation factor | |||
| 60 Hz | 5.0E-4 | ASTM D150 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 500 V/sec |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |