| About |
|---|
| LNP THERMOTUF QX01581H is a compound based on Nylon 6/10 resin containing Glass Fiber. Added features of this material include: High Impact. Also known as: LNP* THERMOTUF* Compound PDX-Q-01581 Product reorder name: QX01581H&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PA610 |
| Material Status | Commercial: Active |
| Features | High impact resistance |
| Availabilitys | Asia Pacific |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.30 | g/cm³ | ASTM D792 , ISO 1183 |
| Shrinkage rate | |||
| MD：24 hrs | 0.10 to 0.30 | % | ASTM D955 |
| TD：24 hrs | 0.90 to 1.1 | % | ASTM D955 |
| MD：24 hrs | 0.10 to 0.30 | % | ISO 294-4 |
| Water absorption rate | |||
| 24hr，50% RH | 0.20 | % | ASTM D570 |
| Equilibrium, 23 ℃, 50% RH | 0.30 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| — | 8480 | MPa | ASTM D638 |
| — | 7880 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 140 | MPa | ASTM D638 |
| fracture | 134 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 3.4 | % | ASTM D638 |
| fracture | 3.6 | % | ISO 527-2 |
| Bending modulus | |||
| — | 7030 | MPa | ASTM D790 |
| — | 7250 | MPa | ISO 178 |
| bending strength | |||
| — | 207 | MPa | ASTM D790 |
| — | 208 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 360 | J/m | ASTM D256 |
| 23℃ | 15 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | |||
| 23℃ | 1200 | J/m | ASTM D4812 |
| 23℃ | 73 | kJ/m² | ISO 180/1U |
| Dart impact equipped with measuring instruments | |||
| 23℃，Energy at Peak Load | 9.30 | J | ASTM D3763 |
| — | 3.52 | J | ISO 6603-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 3.2 mm | 208 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed, 64 mm span | 205 | ℃ | ISO 75-2/Af |
| Linear coefficient of thermal expansion | |||
| MD：-40~40℃ | 3.1E-5 | 1/℃ | ASTM E831 |
| MD：-40~40℃ | 3.2E-5 | 1/℃ | ISO 11359-2 |
| TD：-40~40℃ | 8.8E-5 | 1/℃ | ASTM E831，ISO 11359-2 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |