| About |
|---|
| Asrene® UF 1810 is a Linear Low Density Polyethylene product. It is available in Asia Pacific, Europe, or North America. Applications of Asrene® UF 1810 include film, coating applications and wrap. Characteristics include: Butene Comonomer Clarity Good Toughness&& |
| Product Description | |
|---|---|
| Generic | Linear low density polyethylene |
| Material Status | Commercial: Active |
| Features | Good Clarity,Good flexibility,Low speed solidification point,Butylene copolymer |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.919 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 1.0 | g/10min | ASTM D1238 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| friction coefficient | |||
| Blown film | 0.60 | ASTM D1894 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 30 | µm | |
| tensile strength | ASTM D882 | ||
| MD : Break, 1.2 mil, Blown Film | 50.0 | MPa | ASTM D882 |
| TD, fracture, 30 µ m, blow molded film | 24.0 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD : Break, 1.2 mil, Blown Film | 700 | % | ASTM D882 |
| TD, fracture, 30 µ m, blow molded film | 850 | % | ASTM D882 |
| Drop hammer impact | |||
| 30 µ m, blow molded film | 100 | g | ASTM D1709 |
| tear strength | ASTM D1922 | ||
| MD，30 µm | 24.5 | kN/m | ASTM D1922 |
| TD，30 µm | 196.1 | kN/m | ASTM D1922 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | < -70.0 | ℃ | ASTM D746 |
| Vicat Softening Temp | 104 | ℃ | ASTM D1525 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45 °, 30 µ m, blow molded film | 72 | ASTM D2457 | |
| transparency | |||
| 30.0 µ m, blow molded film | 75.0 | ASTM D1746 | |
| Haze | |||
| 30 µ m, blow molded film | 11 | % | ASTM D1003 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Melt temperature | 170 to 200 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Blown Film |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |