| About |
|---|
| Trademark PE mLLD1918B is a Metallocene Linear Low Density Polyethylene product. It can be processed by coextrusion and is available in North America. Applications of Trademark PE mLLD1918B include film, food contact applications, packaging and sealing applications. Characteristics include: Food Contact Acceptable Good Sealability High Gloss High Strength Processing Aid&& |
| Product Description | |
|---|---|
| Generic | mLLDPE |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good surface appearance,Good heat sealing,Food contact compliance |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.918 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 1.0 | g/10min | ASTM D1238 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 25 | µm | |
| Membrane puncture force | |||
| 25 µm | 77.0 | N | ASTM D3763 |
| Secant modulus | ASTM D882 | ||
| 1% secant, MD: 25 µ m, blow molded film | 172 | MPa | ASTM D882 |
| 1% secant, TD: 25 µ m, blow molded film | 190 | MPa | ASTM D882 |
| tensile strength | ASTM D882 | ||
| MD, yield, 25 µ m, blow molded film | 10.7 | MPa | ASTM D882 |
| TD, yield, 25 µ m, blow molded film | 9.51 | MPa | ASTM D882 |
| MD, fracture, 25 µ m, blow molded film | 58.5 | MPa | ASTM D882 |
| TD, fracture, 25 µ m, blow molded film | 51.6 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, fracture, 25 µ m, blow molded film | 450 | % | ASTM D882 |
| TD, fracture, 25 µ m, blow molded film | 600 | % | ASTM D882 |
| Drop hammer impact | |||
| 25 µ m, blow molded film | 800 | g | ASTM D1709 |
| Elmandorf tear strength | ASTM D1922 | ||
| MD: 25 µ m, blow molded film | 230 | g | ASTM D1922 |
| TD: 25 µ m, blow molded film | 500 | g | ASTM D1922 |
| Initial sealing temperature | |||
| 25 µ m, blow molded film | 95.6 | ℃ | ASTM D3763 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45 °, 25.4 µ m, blow molded film | 130 | ASTM D2457 | |
| Haze | |||
| 25.4 µ m, blow molded film | 4.0 | % | ASTM D1003 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Melt temperature | 182 to 204 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Base polymer only |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |