| About |
|---|
| 40 Shore D TPE (Thermoplastic Vulcanizate). Available in black, natural or pre-colored for injection molding and extrusion applications. This rigid material is non-hygroscopic and offers excellent chemical resistance and physical properties. EZPrene is polyolefin based and is 100% recyclable.&& |
| Product Description | |
|---|---|
| Generic | TPV |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Weather resistance is good,Good Dimensional Stability,Renewable resources,Low or no water absorption,Good bond,Ozone resistance,Solvent resistance,Good coloring |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.960 | g/cm³ | ASTM D792 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| fracture | 18.0 | MPa | ASTM D412 |
| 100% strain | 9.00 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 620 | % | ASTM D412 |
| tear strength | 80.0 | kN/m | ASTM D624 |
| Compression deformation | ASTM D395 | ||
| 23℃，22 hr | 55 | % | ASTM D395 |
| 125℃，70 hr | 75 | % | ASTM D395 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ASTM D2240 | ||
| Shore D, 5 seconds, extrusion molding | 39 | ASTM D2240 | |
| Shore D, 5 seconds, injection molding | 41 | ASTM D2240 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -35.0 | ℃ | ASTM D746 |
| Dynamic Service Temperature | 130 | ℃ |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Ozone resistance | Excellent | ASTM D1149 |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Injection | Nominal value | Unit | Test method |
| Hopper temperature | 166 to 177 | °C | |
| Barrel 1 zone temperature | 171 to 191 | °C | |
| Barrel 2 zone temperature | 171 to 191 | °C | |
| Barrel 3 zone temperature | 171 to 191 | °C | |
| Barrel 4 zone temperature | 171 to 191 | °C | |
| Barrel 5 zone temperature | 171 to 191 | °C | |
| Connector temperature | 191 to 210 | °C | |
| Melt temperature | 191 to 199 | °C | |
| Nozzle temperature | 191 to 210 | °C | |
| Drying temperature | 82 | °C | |
| Drying time | 2.0 to 3.0 | hr | |
| Barrel rear temperature | 191 to 204 | °C | |
| Barrel middle temperature | 196 to 210 | °C | |
| Barrel front temperature | 196 to 210 | °C | |
| Nozzle temperature | 210 to 221 | °C | |
| Processing (melt) temperature | 199 to 221 | °C | |
| Mold temperature | 24 to 52 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |