TECHNYL STAR® AF 60SX V30 GREY 7035 LPU

About
TECHNYL STAR® AF 60SX V30 GREY 7035 LPU is a polyamide 66 based on a non halogenated flame retardant system, reinforced with 30% of glass fiber, for injection moulding. This grade offers, in addition to a high flow matrix and a good combination of fire properties, the particularity to decrease the level of blooming/exudation phenomena during the life time of the application.&&

Product Description
Supplier	DOMO
Generic	PA66
Material Status	Commercial: Active
Features	Low Halogen Content,High liquidity,Good stripping performance,Good surface appearance
Availabilitys	Europe,Africa & Middle East
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.46	g/cm³
Shrinkage rate
TD	1.0	%
MD	0.30	%
Water absorption rate
23℃，24hr	0.70	%
Saturation, 23 ℃	4.1	%
Equilibrium, 23 ℃, 50% RH	1.7	%

MECHANICAL	Nominal value	Unit
Tensile modulus
23℃	10800	MPa
tensile strength
Fracture, 23 ℃	105	MPa
Tensile strain
Fracture, 23 ℃	1.5	%

IMPACT	Nominal value	Unit	Test method
Charpy Unnotch Impact strength
23℃	33	kJ/m²

THERMAL	Nominal value	Unit
Hot deformation temperature
0.45 MPa, unannealed	262	℃
1.8 MPa, unannealed	243	℃
Melting temperature	263	℃

Electrical performance	Nominal value	Unit
Dielectric strength
0.8 mm	37	kV/mm
Compared to the leakage tracing index
Solution A	600	V

FLAME CHARACTERISTICS	Nominal value	Unit
Flame retardant level
0.80 mm	V-0
1.60 mm
3.20 mm
Glowing wire flammability index
0.80 mm	960	℃
1.6 mm	960	℃
3.2 mm	960	℃
Igniting temperature of the hot wire
0.8 mm	750	℃
Extreme oxygen index	33	%

Supplementary information	Nominal value	Unit	Test method
European Railway Certification
R22	HL3
R23	HL3

Process Conditions
Injection	Nominal value	Unit	Test method
Injection instructions	Nominal value	Unit	Test method
drying temperature	80	°C
Recommended maximum moisture content	0.20	%
Temperature at the rear of the barrel	260 to 270	°C
Temperature in the middle of the barrel	265 to 275	°C
Front temperature of material barrel	265 to 280	°C
Mold temperature	60 to 90	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.