| About |
|---|
| Product Description: TREXPRENE ® A88CW is a heat and UV stabilized PP/EPDM based Thermoplastic Vulcanized Elastomer (TPV) and is primarily intended for Exterior applications. This material can be processed using Extrusion, Injection, or Blow Molding equipment.&& |
| Product Description | |
|---|---|
| Supplier | Mitsubishi |
| Generic | TPV |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Heat Stabilized |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.940 to 1.00 | g/cm³ | ISO 1183 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ISO 37 | ||
| TD, 100% strain | 5.60 | MPa | ISO 37 |
| MD, 100% strain | 6.00 | MPa | ISO 37 |
| tensile strength | ISO 37 | ||
| TD, yield | 13.1 | MPa | ISO 37 |
| MD, yield | 9.00 | MPa | ISO 37 |
| Tensile strain | ISO 37 | ||
| fracture | > 490 | % | ISO 37 |
| Flow rate, fracture | > 350 | % | ISO 37 |
| tear strength | ISO 34-1 | ||
| TD | 45 | kN/m | ISO 34-1 |
| MD | 45 | kN/m | ISO 34-1 |
| Compression deformation | |||
| 125℃，70 hr | < 80 | % | ISO 815 |
| 125℃，70 hr | < 80 | % | ASTM D395B |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore A, 5 seconds | 84 to 92 | ISO 868 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -52.0 | ℃ | ASTM D746 |
| Brittleness Temperature（Type B） | -52.0 | ℃ | ISO 812 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Burning rate | 35 | mm/min | FMVSS 302 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Accelerated aging time | Delta E < 3 | SAE J2527 | |
| Color stability | |||
| to Light | No Objectionable Defects | SAE J1885 | |
| Ozone resistance | |||
| 40℃ | 0 Rating | ISO 1431-1 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Type 1, 20 in/min |
| 3. Method Ba, Angle (Unnicked), 20 in/min |
| 4. Type A |
| 5. Extended UV Filters, 2500 kJ/m 2 |
| 6. Xenon Arc 1240.8kJ/m² |
| 7. 100 pphm, Method A |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |