SABIC® LLDPE R40039EE

About
SABIC® LLDPE R40039EE is a medium density polyethylene (MDPE) copolymer. It is typically used for its good stress crack resistance, rigidity, gloss and low warpage. The resin contains UV-stabilizer. It is recommended that SABIC® LLDPE R40039E is grinded before use in rotational moulding applications. Typical applications. Because of the good processing performance and physical properties, SABIC® LLDPE R40039EE is typically used for the rotational moulding of large industrial and agricultural tanks, trash containers and chemical shipping drums. Due to the good mechanical properties and low warpage this product is typically used for injection moulding of screw closures, caps and housewares. The UV-stabilization provides good protection for the final product. This product is not intended for and must not be used in any pharmaceutical/medical applications.&&

About

SABIC® LLDPE R40039EE is a medium density polyethylene (MDPE) copolymer. It is typically used for its good stress crack resistance, rigidity, gloss and low warpage. The resin contains UV-stabilizer. It is recommended that SABIC® LLDPE R40039E is grinded before use in rotational moulding applications. Typical applications. Because of the good processing performance and physical properties, SABIC® LLDPE R40039EE is typically used for the rotational moulding of large industrial and agricultural tanks, trash containers and chemical shipping drums. Due to the good mechanical properties and low warpage this product is typically used for injection moulding of screw closures, caps and housewares. The UV-stabilization provides good protection for the final product. This product is not intended for and must not be used in any pharmaceutical/medical applications.&&

Product Description
Supplier	SABIC
Generic	Linear low density polyethylene
Material Status	Commercial: Active
Features	Good Rigidity,Weather resistance is good,Low warping,Good surface appearance,Copolymer,High ESCR
Availabilitys	Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.937	g/cm³	ASTM D1505
Melt Flow Rate
190℃，2.16kg	3.5	g/10min	ASTM D1238
ESCR(Environmental Stress Cracking Resistance)
100% non-ionic detergent, molded, F50	> 150	hr	ASTM D1693B

THERMAL	Nominal value	Unit	Test method
Embrittlement temperature	< -75.0	℃	ASTM D746
Vicat Softening Temp	117	℃	ASTM D1525

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D, molded	69		ASTM D2240
Tensile modulus
1% cut, molded	600	MPa	ASTM D638
tensile strength			ASTM D638
Yield, molding	18.0	MPa	ASTM D638
Fracture, molded	19.0	MPa	ASTM D638
Tensile strain
Fracture, molded	500	%	ASTM D638
Bending modulus
1% cut, molded	710	MPa	ASTM D790

Process Conditions
injection	Nominal value	Unit	Test method
Processing (melt) temperature	210 to 240	°C

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.