Ultramid® 2710IR BRIGHT

About

Product Description
Supplier	BASF
Generic	PA66
Material Status	Commercial: Active
Features	High impact resistance,Quick molding cycle,Good surface appearance
Availabilitys	Asia Pacific
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Water absorption
23 ℃, 24 hours in the water	1.1	%	ISO 62
Balance, 23 ℃, 50% humidity	2.4	%	ISO 62
Density	1100	kg/m³	ISO 1183

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus
Dry	2500	MPa	ISO 527-2
Wet Cond	1100	MPa	ISO 527-2
Tensile strength
	80	MPa	ISO 527-2
	40	MPa	ISO 527-2
Break, wet cond, 2 in/min	62	MPa	ASTM D638
Break, dry dry	80	MPa	ISO 527-2
Break, wet cond	40	MPa	ISO 527-2
Tensile Strain
Yield yld, dry dry dry	10	%	ISO 527-2
Yield yld, wet cond	16	%	ISO 527-2
Break, dry dry	25	%	ISO 527-2
Break, wet cond	>250	%	ISO 527-2
Elongation at break
Dry, 2 in/min	30	%	ASTM D638

	2200	MPa	ISO 178
Wet Cond	1050	MPa	ISO 178
Flexural strength
Dry	90	MPa	ISO 178
Wet Cond	40	MPa	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy notched impact strength
Dry	18	kJ/m²	ISO 179/1eA
Wet Cond	90	kJ/m²	ISO 179/1eA
Izod notched impact strength	250	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature HDT
1.8 MPa	92	℃	ISO 75-1/-2
1.82 MPa	70	℃	ASTM D648
0.45 MPa	210	℃	ISO 75-1/-2
Melting temperature	262	℃	ISO 11357-3

ELECTRICAL	Nominal value	Unit	Test method
Surface resistivity
Dry	1E15	ohm	IEC 62631-3-2
Wet Cond	1E15	ohm	IEC 62631-3-2
Volume resistivity
Dry	1E13	ohm·m	IEC 62631-3-1
Wet Cond	1E13	ohm·m	IEC 62631-3-1

Dry	30	kV/mm	IEC 60243-1
Wet Cond	16	kV/mm	IEC 60243-1
Compared tracking index
Dry, test solution A	550		IEC 60112
	470
Relative permittivity
Dry	3.2		IEC 62631-2-1
Wet Cond	3.2		IEC 62631-2-1

FLAME CHARACTERISTICS	Nominal value	Unit	Test method
Flame Class Rating
3.2 mm	HB	calss	IEC 60695-11-10

Process Conditions
Injection	Nominal value	Unit	Test method
Drying Temperature	80.0	°C
Suggested Maximum Moisture Content	0.20	%
Rear Temperature Zone 1	265 to 270	°C
Middle Temperature Zone 2	270 to 280	°C
Front Temperature Zone 3	280 to 290	°C
Mold Temperature	70.0 to 100	°C

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.