| About |
|---|
| 未增强的PBTP，易流动，易释放，阻燃等级UL94 V-0 |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | polybutylene terephthalate |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good Dimensional Stability,Fatigue resistance |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| Tensile strain | |||
| Fracture, 50 mm/min | 110 | % | ASTM D638 |
| bending strength | |||
| Yield, 50 mm span | 82 | MPa | ASTM D790 |
| Fracture, 50 mm span | 82 | MPa | ASTM D790 |
| Bending modulus | |||
| 2060 | MPa | ASTM D790 | |
| Rockwell hardness | 117 | ASTM D785 | |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Notched impact strength of cantilever beam | |||
| 23℃ | 3204 | J/m | ASTM D4812 |
| Impact strength of cantilever beam notch | |||
| 23℃ | 534 | J/m | ASTM D256 |
| Gardner, 23 ℃ | 43 | J | ASTM D 3029 |
| Improved Gardner | |||
| 23℃ | 43 | J | ASTM D 3029 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Relative temperature index | |||
| Electrical performance | 120 | ℃ | UL 746B |
| Impact mechanical performance | 120 | ℃ | UL 746B |
| Non mechanical impact performance | 120 | ℃ | UL 746B |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.34 | g/cm³ | ASTM D792 |
| Specific product | 0.75 | cm³/g | ASTM D 792 |
| Water absorption rate | |||
| 24hr | 0.08 | % | ASTM D570 |
| Shrinkage rate | |||
| MD：0.75-2.3 mm | 0.8 – 1.1 | % | Internal Method |
| MD：2.3-4.6 mm | 1 – 1.4 | % | Internal Method |
| TD：0.75-2.3 mm | 0.9 – 1.3 | % | Internal Method |
| TD：2.3-4.6 mm | 1.2 – 1.6 | % | Internal Method |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | >1.2E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | |||
| 3.2 mm in air | 18.5 | kV/mm | ASTM D149 |
| 1.6 mm in oil | 25 | kV/mm | ASTM D49 |
| 3.2 mm in oil | 18.5 | kV/mm | ASTM D149 |
| Relative permittivity | |||
| 100 Hz | 3.2 | ASTM D150 | |
| 1 MHz | 3.2 | ASTM D150 | |
| Dissipation factor | |||
| 100 Hz | 0.003 | ASTM D150 | |
| 1 MHz | 0.03 | ASTM D150 | |
| Arc resistance | |||
| Tungsten wire | 6 | PLC Code | ASTM D495 |
| Hot wire ignition {PLC} | 2 | PLC Code | UL 746A |
| High voltage arc marking rate {PLC} | 3 | PLC Code | UL 746A |
| High current arc ignition (surface {PLC}) | 3 | PLC Code | UL 746A |
| Compared to the leakage tracing index | 2 | PLC Code | UL 746A |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.45 mm | HB | UL 94 | |
| 0.63 mm | V-0 | UL 94 | |
| 2.99 mm | 5VA | UL 94 | |
| ultraviolet radiation | |||
| Water exposure/immersion | F2 | – | UL 746C |
| Process Conditions | |||
|---|---|---|---|
| injection molding | Nominal value | Unit | Test method |
| Drying temperature | 120 | °C | |
| Drying time | 3-4 | hrs | |
| Drying time (gradually increasing) | 12 | hrs | |
| Maximum water content | 0.02 | % | |
| Melt temperature | 250-265 | °C | |
| Nozzle temperature | 245-260 | °C | |
| Front temperature | 250-265 | °C | |
| Mid section temperature | 245-260 | °C | |
| Post stage temperature | 240-255 | °C | |
| Mold temperature | 50-75 | °C | |
| Back pressure | 0.3-0.7 | MPa | |
| Screw speed | 50-100 | rpm | |
| Shooting cylinder size | 40-80 | % | |
| Depth of exhaust groove | 0.025-0.038 | mm | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |