| About |
|---|
| PRE-ELEC® PP 1384 is a conductive thermoplastic compound based on polypropylene. Conductivity is achieved by using special conductive carbon black. In addition to a low electrical resistivity. PRE-ELEC® PP 1384 has excellent mechanical properties and is easy to extrude. PRE-ELEC® PP 1384 is recommended to be used in polypropylene tape co-extrusion for FIBC (type C) applications.&& |
| Product Description | |
|---|---|
| Supplier | Premix Oy |
| Generic | Polyolefin Elastomer |
| Material Status | Commercial: Active |
| Features | Excellent Processability,Conductive |
| Availabilitys | North America,Latin America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.05 | g/cm³ | ASTM D792 |
| Density | 1.06 | g/cm³ | ISO 1183 |
| Melt Flow Rate | ISO 1133 | ||
| 230℃，2.16kg | 1.0 | g/10min | ISO 1133 |
| 230℃，5.0kg | 16 | g/10min | ISO 1133 |
| Shrinkage rate | |||
| MD | 1.2 to 1.7 | % | ASTM D955 |
| MD | 1.2 to 1.7 | % | ISO 294-4 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ISO 868 | ||
| Shaw’s A | 98 | ISO 868 | |
| Shaw’s D | 73 | ISO 868 | |
| tensile strength | 30.0 | MPa | ISO 527-2 |
| MD | 30.0 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 4.0 | % | ISO 527-2 |
| Bending modulus | |||
| 4 mm | 2500 | MPa | ISO 178 |
| 4 mm | 2480 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| -20℃ | 2.1 | kJ/m² | ASTM D256 |
| -20℃ | 2.0 | kJ/m² | ISO 179 |
| 23℃ | 4.0 | kJ/m² | ISO 179 |
| 23℃ | 4.2 | kJ/m² | ASTM D256 |
| Charpy Unnotch Impact strength | |||
| -20℃ | 4.2 | kJ/m² | ASTM D256 |
| -20℃ | 5.0 | kJ/m² | ISO 179 |
| 23℃ | 14 | kJ/m² | ISO 179 |
| 23℃ | 13 | kJ/m² | ASTM D256 |
| -20℃，4.00 mm | 1.26 | kJ/m² | ASTM D256 |
| 23℃，4.00 mm | 1.47 | kJ/m² | ASTM D256 |
| Impact strength of cantilever beam notch | ISO 180 | ||
| Area | ASTM D256 | ||
| -20℃ | 1.2 | kJ/m² | ISO 180 |
| 23℃ | 1.5 | kJ/m² | ISO 180 |
| Notched impact strength of cantilever beam | ASTM D256 | ||
| -20℃，4 mm | 8.41 | kJ/m² | ASTM D256 |
| 23℃，4 mm | 16.8 | kJ/m² | ASTM D256 |
| Notched impact strength of cantilever beam | ISO 180 | ||
| -20℃ | 9.0 | kJ/m² | ISO 180 |
| 23℃ | 16 | kJ/m² | ISO 180 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 63.0 | ℃ | ISO 75-2/Af |
| 1.8 MPa, unannealed | 62.8 | ℃ | ASTM D648-A |
| 0.45 MPa, unannealed | 109 | ℃ | ISO 75-2/Bf |
| 0.45 MPa, unannealed | 109 | ℃ | ASTM D648-B |
| Vicat Softening Temp | 154 | ℃ | ASTM D1525 4 |
| A50 | 154 | ℃ | ISO 306/A50 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | < 1.0E+2 | ohms | IEC 61340-2-3 |
| Volume resistivity | < 10 | ohms·cm | Internal Method |
| Process Conditions | |||
|---|---|---|---|
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 90 | °C | |
| Drying time | 2.0 | hr | |
| Barrel 1 zone temperature | 210 | °C | |
| Barrel 2 zone temperature | 220 | °C | |
| Barrel 3 zone temperature | 220 | °C | |
| Barrel 4 zone temperature | 230 | °C | |
| Barrel 5 zone temperature | 230 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Flow |
| 3. 4 mm thickness |
| 4. Rate A (50°C/h), Loading 2 (50 N) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |