| About |
|---|
| LEXAN™FL913树脂是一种无定形，紫外线稳定的聚碳酸酯，添加10％玻璃纤维增强。具有高机械，光学，电气和热性能。具有良好的抗冲击性，优异的尺寸稳定性，高弯曲强度，高模量和晶体透明度。通过高刚度重量比提供重量节省。通过结构泡沫成型加工。它是金属的优良替代品，可用于生产结构部件和大型零件，如户外配电柜。 |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | Polycarbonate |
| Material Status | Commercial: Active |
| Features | High impact resistance,High elastic,High modulus |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| tensile strength | |||
| Yield, 6.35 mm | 53 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 6.35 mm | 4.8 | % | ASTM D638 |
| Tensile modulus | |||
| 6.40 mm | 3168.63 | MPa | ASTM D638 |
| bending strength | |||
| Yield, 6.40 mm | 89.271 | MPa | ASTM D790 |
| Bending modulus | |||
| 6.40 mm | 3511.98 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Foam | |||
| Physical 6.4 mm Wt reduction | 10 | % | |
| Hot 6.4 mm Wt reduction | 10 | % | |
| Minimum density of flame level | 0.97 | g/cm³ | |
| Mechanical 6.4 mm Wt reduction | 10 | % | |
| Impact 6.4 mm Wt reduction | 10 | % | |
| Notched impact strength of cantilever beam | |||
| 23℃ | 852.6 | J/m | ASTM D4812 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed, 3.2 mm | 133 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 3.2 mm | 140 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | |||
| MD：-40~95℃ | 3.24E-05 | 1/℃ | ASTM E831 |
| specific heat | 1.19 | J/g-℃ | ASTM C 351 |
| Thermal conductivity coefficient | 0.13 | W/m/℃ | ASTM C 177 |
| Relative temperature index | |||
| Non mechanical impact performance | 80 | ℃ | UL 746B |
| Electrical performance | 80 | ℃ | UL 746B |
| Impact mechanical performance | 80 | ℃ | UL 746B |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.25 | ASTM D 792 | |
| Foam forming | 1.12 | ASTM D792 | |
| Water absorption rate | |||
| 24hr | 0.16 | % | ASTM D570 |
| Water absorption rate | |||
| Equilibrium, 23 ℃ | 0.32 | % | ASTM D570 |
| Shrinkage rate | |||
| MD：6.4 mm | 0.4 – 0.6 | % | Internal Method |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 94V-0 flame level assessment | 3.86 | mm | UL 94 |
| Flame retardant rating, 94v –5VA flame rating evaluation | 3.86 | mm | UL 94 |
| ultraviolet radiation | |||
| Water exposure/immersion | F1 | UL 746C |
| Process Conditions | |||
|---|---|---|---|
| structural foam | Nominal value | Unit | Test method |
| Foaming agents, physical systems | 氮气 | ||
| Foaming agents, chemical systems | FLC95 | ||
| Drying time (foaming agent) | 4 | hrs | |
| Drying temperature (foaming agent) | 105 | °C | |
| Concentration range (foaming agent) | 3 – 5 | % | |
| Recommended concentration (foaming agent) | 1.5 | % | |
| Drying temperature (resin) | 120 | °C | |
| Drying time (resin) | 3 – 4 | hrs | |
| Drying time (resin, accumulated) | 48 | hrs | |
| Melt temperature | 290 – 315 | °C | |
| Nozzle temperature | 270 – 295 | °C | |
| Front Section Zone 3 Temperature | 295 – 310 | °C | |
| Temperature in Zone 2 of the middle section | 295 – 310 | °C | |
| Temperature in Zone 1 of the rear section | 255 – 265 | °C | |
| Mold temperature | 70 – 95 | °C | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |