Celstran® PA66-GF50-02 P7/12

About
Material code according to ISO 1043-1: PA66 Heat stabilized Nylon 66 reinforced by 50 weight percent long glass fibers. The pellets are cylindrical and normally as well as the embedded fibers 7 mm long. Parts molded of CELSTRAN have outstanding mechanical properties such as high strength and stiffness combined with high heat deflection. The notched impact strength is increased at elevated and low temperatures due to the fiber skeleton built in the parts. The long fiber reinforcement reduces creep significantly. The very isotropic shrinkage in the molded parts minimizes the warpage. Complex parts can be manufactured with high reproducibility by injection molding. Can be used for substituting die cast metal with the advantage of Weight reduction, no corrosion problems, no post treatment.&&

About

Material code according to ISO 1043-1: PA66 Heat stabilized Nylon 66 reinforced by 50 weight percent long glass fibers. The pellets are cylindrical and normally as well as the embedded fibers 7 mm long. Parts molded of CELSTRAN have outstanding mechanical properties such as high strength and stiffness combined with high heat deflection. The notched impact strength is increased at elevated and low temperatures due to the fiber skeleton built in the parts. The long fiber reinforcement reduces creep significantly. The very isotropic shrinkage in the molded parts minimizes the warpage. Complex parts can be manufactured with high reproducibility by injection molding. Can be used for substituting die cast metal with the advantage of Weight reduction, no corrosion problems, no post treatment.&&

Product Description
Supplier	Celanese
Generic	PA66
Material Status	Commercial: Active
Features	Good Rigidity,Low warping,Good flexibility,High impact resistance,low-temperature impact resistance,Heat Stabilized
Availabilitys	North America,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.56	g/cm³	ISO 1183

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus	16500	MPa	ISO 527-2/1A/1
tensile strength
fracture	250	MPa	ISO 527-2/1A/5
Tensile strain
fracture	2.0	%	ISO 527-2/1A/5
Bending modulus
23℃	14600	MPa	ISO 178
bending strength
23℃	410	MPa	ISO 178

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength
23℃	42	kJ/m²	ISO 179/1eA

THERMAL	Nominal value	Unit	Test method
Melting temperature	260	℃	ISO 11357-3

Process Conditions
injection	Nominal value	Unit	Test method
Drying temperature	70 to 80	°C
Drying time	2.0 to 4.0	hr
Recommended maximum moisture content	0.15	%
Hopper temperature	70 to 80	°C
Barrel rear temperature	280 to 285	°C
Barrel middle temperature	280 to 290	°C
Barrel front temperature	290 to 300	°C
Nozzle temperature	310 to 320	°C
Processing (melt) temperature	310 to 320	°C
Mold temperature	90 to 120	°C
Injection pressure	120 to 150	MPa
Injection speed	Moderate
Hold pressure	50.0 to 80.0	MPa
Back pressure	0.00 to 3.00	MPa

Notes
1. Typical properties: these are not to be construed as specifications.
2. 10°C/min
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.