| About |
|---|
| This compound is designed for overmold to nylon.&& |
| Product Description | |
|---|---|
| Supplier | Teknor Apex |
| Generic | TPE |
| Material Status | Commercial: Active |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.908 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 0.20 | g/10min | ASTM D1238 |
| Shrinkage rate | ASTM D955 | ||
| MD | 1.8 | % | |
| TD | 1.8 | % | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s A | 45 | ASTM D2240 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | ASTM D412 | ||
| fracture | 4.83 | MPa | ASTM D412 |
| 100% strain | 1.52 | MPa | |
| 200% strain | 2.21 | MPa | |
| 300% strain | 2.93 | MPa | |
| Tensile strain | |||
| fracture | 600 | % | ASTM D412 |
| tear strength | 25.4 | kN/m | ASTM D624 |
| Compression deformation | |||
| 23℃，22 hr | 18 | % | ASTM D395 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Adhesion to Nylon |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 60.0 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Barrel rear temperature | 193 to 216 | °C | |
| Barrel middle temperature | 260 to 282 | °C | |
| Barrel front temperature | 271 to 293 | °C | |
| Nozzle temperature | 282 to 302 | °C | |
| Processing (melt) temperature | 282 to 302 | °C | |
| Mold temperature | 21.1 to 37.8 | °C | |
| Injection pressure | 1.38 to 5.52 | MPa | |
| Back pressure | 0.172 to 0.689 | MPa | |
| Screw speed | 50 to 100 | rpm | |
| Cushion | 3.81 to 25.4 | mm | |
| Barrel 1 zone temperature | 193 to 216 | °C | |
| Barrel 2 zone temperature | 249 to 271 | °C | |
| Barrel 3 zone temperature | 260 to 282 | °C | |
| Barrel 5 zone temperature | 271 to 293 | °C | |
| Nozzle temperature | 271 to 293 | °C | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |