| About |
|---|
| Economical, extrusion & injection, fully vulcanized EPDM/PP series Additive Packages : T / Heat and UV stabilizer Key Features : Rubberlike elasticity Ease of coloring by proper MB (PE,PP,etc. based) Low compression set Easy of processing Recyclability&& |
| Product Description | |
|---|---|
| Material Status | Commercial: Active |
| Features | Renewable resources,Good Dimensional Stability,Good coloring,Solvent resistance,Heat Stabilized,High elastic,Weather resistance is good,Excellent Processability |
| Availabilitys | Europe |
| Process Methods | Injection Molding,Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.970 | g/cm³ | ISO 2781 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore A, 3 seconds | 50 | ISO 868 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| fracture | 5.70 | MPa | ISO 37 |
| 100% strain | 1.50 | MPa | |
| 300% strain | 2.50 | MPa | |
| Tensile strain | |||
| fracture | 600 | % | ISO 37 |
| tear strength | |||
| TD | 28 | kN/m | ISO 34-1 |
| Compression deformation | |||
| -25℃，22 hr | 69 | % | |
| 23℃，72 hr | 17 | % | |
| 70℃，22 hr | 30 | % |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air | |||
| 100℃，168 hr | 1.8 | % | ISO 188 |
| Changes in tensile stress during fracture in air | |||
| 100℃，168 hr | 610 | % | ISO 188 |
| The rate of change of Shore hardness in air | |||
| Shore A, -10 ℃, 22 hr | -3.0 | ||
| Shaw A, 100 ℃, 168 hr | -3.0 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -45.0 | ℃ | |
| Operating temperature | |||
| Dynamic | 110 | ℃ | |
| Static | 135 | ℃ |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| Injection instructions | Nominal value | Unit | Test method |
| drying temperature | 80 to 90 | °C | |
| Drying time | 2.0 | hr | |
| Hopper temperature | 170 to 180 | °C | |
| Temperature in the middle of the barrel | 180 to 190 | °C | |
| Front temperature of material barrel | 190 to 200 | °C | |
| Nozzle temperature | 200 to 210 | °C | |
| Processing (melt) temperature | 210 to 220 | °C | |
| Mold temperature | 10 to 50 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |