| About |
|---|
| TECHNYL® C 218 V35 Black 21N is a polyamide 6, reinforced with 35% of glass fiber, heat stabilized, for injection moulding. The product offers an excellent combination between thermal and mechanical properties.&& |
| Product Description | |
|---|---|
| Supplier | DOMO |
| Generic | PA6 |
| Material Status | Commercial: Negative |
| Features | Heat Stabilized,Good liquidity,Good stripping performance |
| Availabilitys | Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.41 | g/cm³ | ISO 1183/A |
| Water absorption rate | ISO 62 | ||
| 23℃，24hr | 0.90 | % | ISO 62 |
| Saturation, 23 ℃ | 2.1 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 1.9 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 23℃ | 11000 | MPa | ISO 527-2/1A |
| tensile strength | |||
| Fracture, 23 ℃ | 195 | MPa | ISO 527-2/1A |
| Tensile strain | |||
| Fracture, 23 ℃ | 3.0 | % | ISO 527-2 |
| Bending modulus | |||
| 23℃ | 9600 | MPa | ASTM D790 |
| 23℃ | 9600 | MPa | ISO 178 |
| bending strength | |||
| 23℃ | 260 | MPa | ASTM D790 |
| 23℃ | 280 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 17 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | |||
| 23℃ | 83 | kJ/m² | ISO 179/1eU |
| 23℃ | 74 | kJ/m² | ISO 179/1fU |
| Impact strength of cantilever beam notch | |||
| 23℃ | 15 | kJ/m² | ISO 180 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 205 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 210 | ℃ | ISO 75-2/Af |
| Melting temperature | 222 | ℃ | ISO 11357-3 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+14 | ohms | IEC 60093 |
| Volume resistivity | 1.0E+15 | ohms·cm | IEC 60093 |
| Dielectric strength | |||
| 2 mm | — | kV/mm | IEC 60243-1 |
| Dissipation factor | 0.020 | IEC 60250 | |
| Compared to the leakage tracing index | |||
| Solution A | 550 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Glowing wire flammability index | IEC 60695-2-12 | ||
| 1.6 mm | 650 | ℃ | IEC 60695-2-12 |
| 3.2 mm | 650 | ℃ | IEC 60695-2-12 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |