| About |
|---|
| Adell Polyamide AM-10 is a Polyamide 66 (Nylon 66) material. It is available in North America. Important attributes of Adell Polyamide AM-10 are: Flame Retardant Lubricated&& |
| Product Description | |
|---|---|
| Generic | PA66 |
| Material Status | Commercial: Active |
| Features | Flame Characteristics,Lubricating |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.16 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD | 1.1 to 1.4 | % | ASTM D955 |
| Water absorption rate | |||
| 24hr | 1.1 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃，3.2mm | 37 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648 | ||
| 0.45 MPa, unannealed | 196 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 78.9 | ℃ | ASTM D648 |
| Melting temperature | 254 to 266 | ℃ | |
| Linear coefficient of thermal expansion | |||
| MD | 7.2E-5 | 1/℃ | ASTM D696 |
| Thermal conductivity coefficient | 0.25 | W/m/K | ASTM C177 |
| Relative temperature index | |||
| Electrical performance, 3.00 mm | 105 | ℃ | UL 746 |
| Impact mechanical performance, 3.00 mm | 70.0 | ℃ | UL 746 |
| 3.00 mm | 70.0 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 2.0E+14 | ohms·cm | ASTM D257 |
| Dielectric strength | 18 | kV/mm | ASTM D149 |
| Arc resistance | |||
| 3.05 mm | 150 | sec | ASTM D495 |
| Compared to the resistance to leakage and marking index | |||
| 3.05 mm | 600 | V | UL 746 |
| High Arc Burning Index (HAI) (3.05 mm) | 120 | UL 746 | |
| High voltage arc marking rate (HVTR) (3.05 mm) | 17.0 | mm/min | UL 746 |
| Hot wire ignition (HWI) (3.05 mm) | 45 | sec | UL 746 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | ASTM D785 | ||
| M-level | 85 | ASTM D785 | |
| R-level | 121 | ASTM D785 | |
| tensile strength | |||
| yield | 89.6 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 8.0 | % | ASTM D638 |
| Bending modulus | 3170 | MPa | ASTM D790 |
| bending strength | |||
| yield | 117 | MPa | ASTM D790 |
| compressive strength | 103 | MPa | ASTM D695 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |