| About |
|---|
| Glastic 1580 is an easily fabricated laminate that exhibits excellent flame resistance. This flame-resistant laminate meets the UL94 V0 specification of Underwriters Laboratories. This material was originally designed to meet the television industry’s safety assurance requirements. Glastic 1580 has exceptional flame resistance, arc resistance and a high temperature capability for applications such as flyback transformers and arc stack assemblies.&& |
| Product Description | |
|---|---|
| Generic | 热固性聚酯 |
| Material Status | Commercial: Active |
| Features | Flame Characteristics,Arc resistance,Electric mark,V-0 |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.83 | g/cm³ | ASTM D792 |
| Water absorption rate | |||
| 24hr | 0.20 | % | ASTM D570 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| Yield, 1.60 mm | 57.9 | MPa | ASTM D638 |
| bending strength | |||
| Yield, 1.60 mm | 170 | MPa | ASTM D790 |
| compressive strength | |||
| 1.60 mm | 215 | MPa | ASTM D695 |
| shear strength | 82.7 | MPa | ASTM D732 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 1.6mm | 480 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Linear coefficient of thermal expansion | |||
| MD：1.6 mm | 2.0E-5 | 1/℃ | ASTM D696 |
| Thermal conductivity coefficient | 0.27 | W/m/K | ASTM C177 |
| Relative temperature index | |||
| Electrical performance, 1.60 mm | 120 | ℃ | UL 746 |
| 1.60 mm | 140 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | ASTM D149 | ||
| 1.6 mm in air | 17 | kV/mm | ASTM D149 |
| 1.6 mm in oil | 23 | kV/mm | ASTM D149 |
| Dissipation factor | ASTM D150 | ||
| 1.60 mm，60 Hz | 0.011 | ASTM D150 | |
| 1.60 mm，1 MHz | 0.010 | ASTM D150 | |
| Arc resistance | |||
| 1.60 mm | 181 | sec | ASTM D495 |
| Compared to the resistance to leakage and marking index | |||
| 1.60 mm | 500 | V | UL 746 |
| High Arc Burning Index (HAI) (1.60 mm) | 200 | UL 746 | |
| Hot wire ignition (HWI) (1.60 mm) | 300 | sec | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.60 mm | V-0 | UL 94 | |
| Extreme oxygen index | |||
| 1.6 mm | 39 | % | ASTM D2863 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Method A (Short-Time) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |