| About |
|---|
| 30%GLASS FIBER REINFORCED PA66/PP ALLOY WITH REDUCED WATER ABSORBTION,DIMENSION STABILITY AND UV STABILIZED FOR INJECTION MOULDING APPLICATIONS.&& |
| Product Description | |
|---|---|
| Supplier | Ram-On |
| Generic | PA 66+PP |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Good Dimensional Stability,Low or no water absorption,HB |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.31 | g/cm³ | ASTM D792 |
| Density | 1.31 | g/cm³ | ISO 1183 |
| Shrinkage rate | 0.30 to 0.50 | % | ISO 2577 |
| MD | 0.30 to 0.50 | % | ASTM D955 |
| Water absorption rate | |||
| Saturation, 23 ℃ | 3.0 | % | ISO 62 |
| saturated | 3.0 | % | ASTM D570 |
| Equilibrium, 23 ℃, 50% RH | 1.2 | % | ASTM D570 |
| Equilibrium, 23 ℃, 50% RH | 1.2 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 13 | kJ/m² | ISO 180 |
| 23℃ | 130 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Maximum Use Temperature（Short Peaks Operation） | 150 | ℃ | |
| Melting peak temperature | 256 | ℃ | ASTM D3418 |
| Melting temperature | 256 | ℃ | ISO 11357-3 |
| Maximum continuous usage temperature | 80 | ℃ |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 3.00 mm | HB | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| yield | 145 | MPa | ASTM D638 |
| yield | 145 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 3.0 | % | ASTM D638 |
| fracture | 3.0 | % | ISO 527-2 |
| Bending modulus | 5700 | MPa | ASTM D790 |
| Bending modulus | 5700 | MPa | ISO 178 |
| bending strength | 195 | MPa | ASTM D790 |
| bending strength | 195 | MPa | ISO 178 |
| Rockwell hardness | |||
| R-level | 121 | ASTM D785 | |
| R-level | 121 | ISO 2039-2 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |