| About |
|---|
| Overview: MAGNUM™ 3325SLG is a medium heat ABS. Its very low gloss combined with a high flow makes it specifically suitable for unpainted interior automotive applications. MAGNUM™ 3325SLG can thereby help you to save up to 50% of the part costs. Benefits: Lot to lot consistency allowing for optimal machine parameters settings from the start Self-coloring enabling improvement of costs by using less pigments and lowering your logistic costs Low VOC allowing a better interior air quality facing increasing regulatory and OEMs constraints. Heat stability during wide range of processing temperatures: enhanced part design freedom High scratch and mar resistance for an improved aesthetic durability of the parts Easier recyclability of unpainted part Applications: Matt/unpainted interior automotive applications Mid-consoles Pillars Door liners Glove boxes&& |
| Product Description | |
|---|---|
| Supplier | Trinseo |
| Generic | ABS |
| Material Status | Commercial: Active |
| Features | Heat Resistance, Good,Low Gloss |
| Availabilitys | North America,Latin America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.05 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD | 0.52 | % | ASTM D995 |
| TD | 0.53 | % | ASTM D995 |
| Melt Flow Rate | |||
| 230℃，3.80kg | 3.1 | g/10min | ASTM D1238 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| 23℃ | 40.0 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 23 ℃ | 2.8 | % | ASTM D638 |
| Tensile modulus | |||
| 23℃ | 2080 | MPa | ASTM D638 |
| bending strength | |||
| 23℃ | 64.1 | MPa | ASTM D790 |
| Bending modulus | |||
| 23℃ | 2140 | MPa | ASTM D790 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 96.7 | ℃ | ASTM D648 |
| 1.8 MPa, unannealed | 82.2 | ℃ | ASTM D648 |
| Vicat Softening Temp | |||
| 101 | ℃ | ASTM D1525 | |
| Linear coefficient of thermal expansion | |||
| MD | 8.3E-5 | 1/℃ | ASTM D696 |
| TD | 9.0E-5 | 1/℃ | ASTM D696 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 190 | J/m | ASTM D256 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 85.0 | °C | |
| Drying time | 3.0-4.0 | Hr | |
| Injection temperature | |||
| Rear barrel temperature | 180-190 | °C | |
| Central temperature of the barrel | 190-220 | °C | |
| Barrel front temperature | 190-220 | °C | |
| Die temperature | 200-230 | °C | |
| Mold temperature | 60-80 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 3. Method I (3 point load), 0.051 in/min |
| 4. 0.079 in/min |
| 5. 3-points |
| 6. Rate A (50°C/h), Loading 2 (50 N) |
| 7. This rating not intended to reflect hazards presented by this or any other material under actual fire conditions. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |