| About |
|---|
| KetaSpire® KT-880 GF20 is a high flow, 20% glass-fiber reinforced grade of polyetheretherketone (PEEK). This resin offers higher strength and stiffness properties relative to unreinforced KetaSpire® PEEK resin. The glass fiber content is optimized to provide a balance of strength and stiffness with toughness-related properties, such as impact resistance and elongation at break. This level of reinforcement also affords greater mechanical robustness in structural applications, particularly those with service temperatures approaching 240°C (464°F). KetaSpire® PEEK is produced to the highest industry standards and is characterized by a distinct combination of properties, which include excellent wear resistance, best-in-class fatigue resistance, ease of melt processing, high purity and excellent chemical resistance to organics, acids and bases. These properties make it well-suited for applications in healthcare, transportation, electronics, chemical processing and other industrial uses.&& |
| Product Description | |
|---|---|
| Supplier | Solvay |
| Material Status | Commercial: Active |
| Features | Steam sterilized,Resistance to the steam,Gamma radiation,Good disinfection,Good Dimensional Stability,Heat sterilization,Fatigue resistance,Ethylene oxide disinfection,Radioactive,Radiation disinfection,Solvent resistance,Biocompatible,Flame Characteristics,E-beam disinfection,Good Rigidity,High pressure disinfection,High Heat Resistance,High liquidity |
| Availabilitys | Europe,Africa & Middle East ,North America,Asia Pacific,Latin America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| IMPACT | Nominal value | Unit | Test method |
| Charpy Unnotch Impact strength | 60 | kJ/m² | ISO 179 |
| Impact strength of cantilever beam notch | |||
| — | 60 | J/m | ASTM D256 |
| — | 6.0 | kJ/m² | ISO 180 |
| Notched impact strength of cantilever beam | 770 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | 345 | ℃ | ISO 11357 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 5.0E+15 | ohms | ASTM D257 |
| Volume resistivity | 7.0E+15 | ohms·cm | ASTM D257 |
| Dielectric strength | 310 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 60 Hz | 3.34 | ASTM D150 | |
| 1 kHz | 3.35 | ASTM D150 | |
| 1 MHz | 3.35 | ASTM D150 | |
| Dissipation factor | ASTM D150 | ||
| 60 Hz | 2.0E-3 | ASTM D150 | |
| 1 kHz | 1.0E-3 | ASTM D150 | |
| 1 MHz | 4.0E-3 | ASTM D150 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-level | 103 | ASTM D785 | |
| Tensile modulus | |||
| — | 8200 | MPa | ASTM D638 |
| — | 8300 | MPa | ISO 527-2 |
| tensile strength | |||
| fracture | 152 | MPa | ASTM D638 |
| fracture | 162 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | 3.7 | % | ASTM D638 |
| fracture | 3.5 | % | ISO 527-2/1A/5 |
| Bending modulus | |||
| — | 7860 | MPa | ASTM D790 |
| — | 7720 | MPa | ISO 178 |
| bending strength | |||
| — | 254 | MPa | ASTM D790 |
| — | 238 | MPa | ISO 178 |
| Elastic modulus | |||
| — | 8.24 | GPa | ISO 527 |
| — | 8.34 | GPa | ASTM D638 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.46 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 400℃，2.16kg | 18 | g/10min | ASTM D1238 |
| Water absorption rate | |||
| 24hr | 0.022 | % | ISO 15512 |
| Ash Content | 20 | % | ISO 3451-1 |
| Apparent viscosity of melt | |||
| 400℃，1000 sec^-1 | 280 | Pa·s | ASTM D3835 |
| Process Conditions | |||
|---|---|---|---|
| Injection | Nominal value | Unit | Test method |
| Injection speed | Nominal value | Unit | Test method |
| drying temperature | 150 | °C | |
| Drying time | 4.0 | hr | |
| Temperature at the rear of the barrel | 365 | °C | |
| Temperature in the middle of the barrel | 371 | °C | |
| Front temperature of material barrel | 377 | °C | |
| Nozzle temperature | 382 | °C | |
| Mold temperature | 177 to 204 | °C | |
| Screw compression ratio | 2.5:1.0 to 3.5:1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. DSC First heat |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |