| About |
|---|
| Description Non-flammable PP, FB50NHC, FB50NHDI, and FB63FNH, as Non-Halogen non-flammable resin, is eco-friendly and harmless to human body with no non-flammable agent. These products meet Eco-label of Europe such as Blue angel of German, TCO-99 of Sweden, etc. These products equip high rigidity and shock resistance that HIPP Base features and, in particular, fluidity that allows fabulous formability with high non-flammability. Thus, it is widely used for exterior of electric/electronic parts. Characteristics FB50NHC: This Grade has excellent shock resistance in low temperature (-25) and is widely used for construction coupling box, etc. as Non-Halogen non-flammable material belongs to Glow wire ignition index 850 Class of IEC695-2-l standardization. Applications Construction Coupling Box (FB50NHC)&& |
| Product Description | |
|---|---|
| Supplier | HANWHA |
| Generic | Polyolefin Elastomer |
| Material Status | Commercial: Negative |
| Features | Good Rigidity,Good Dimensional Stability,noise reduction,Halogen free,Flame Characteristics,High Heat Resistance,ECO |
| Availabilitys | North America,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.00 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 4.5 | g/10min | ASTM D1238 |
| Shrinkage rate | |||
| MD：2.0 mm | 1.3 to 1.6 | % | Internal Method |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23℃ | 190 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 105 | ℃ | ASTM D648 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.60mm | V-0 | UL-94 | |
| Flammability | 850 | ℃ | IEC 60695-2-1 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| R-level | 86 | ASTM D785 | |
| tensile strength | |||
| yield | 25.5 | MPa | ASTM D638 |
| Tensile strain | |||
| fracture | 80 | % | ASTM D638 |
| Bending modulus | 1440 | MPa | ASTM D790 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 90 to 100 | °C | |
| Drying time | 2.0 | hr | |
| Barrel rear temperature | 170 to 180 | °C | |
| Barrel middle temperature | 180 to 190 | °C | |
| Barrel front temperature | 180 to 200 | °C | |
| Nozzle temperature | 180 to 200 | °C | |
| Mold temperature | 40 to 70 | °C | |
| Injection pressure | 39.2 to 78.5 | MPa | |
| Back pressure | 0.490 to 1.96 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |