| About |
|---|
| Daplen EE188HP is a 15% mineral filled elastomer modified polypropylene compound intended for injection moulding. This material has an excellent balance between impact strength and stiffness and gives a good surface quality.&& |
| Product Description | |
|---|---|
| Supplier | Borealis AG |
| Generic | PP not specified |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good surface appearance,High impact resistance,Renewable resources,High scratch resistance,Low Gloss |
| Availabilitys | Africa & Middle East ,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.02 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 13 | g/10min | ISO 1133 |
| Shrinkage rate | 0.90 | % | Internal Method |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -20℃ | 2.2 | kJ/m² | |
| 23℃ | 22 | kJ/m² | |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -20℃ | 60 | kJ/m² | |
| Impact strength of cantilever beam notch | ISO 180/1A | ||
| -20℃ | 3.2 | kJ/m² | |
| 23℃ | 27 | kJ/m² | |
| Notched impact strength of cantilever beam | ISO 180/1U | ||
| -20℃ | 38 | kJ/m² | |
| 23℃ | 无断裂 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 95.0 | ℃ | ISO 75-2/B |
| 1.8 MPa, unannealed | 54.0 | ℃ | ISO 75-2/A |
| Vicat Softening Temp | |||
| A50 | 132 | ℃ | ISO 306/A50 |
| B50 | 54.0 | ℃ | ISO 306 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| atomization | |||
| 16 hrs，100℃ | mg | DIN 75201 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| discharge | µg/g | VDA 277 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Ball hardness | |||
| H358/30 | 44.0 | MPa | ISO 2039-1 |
| Tensile modulus | 1800 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 22.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| yield | 5.0 | % | ISO 527-2/50 |
| Bending modulus | 1850 | MPa | ISO 178 |
| bending strength | 29.0 | MPa | ISO 178 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 80.0 | °C | |
| Drying time | 2.0 | hr | |
| Processing (melt) temperature | 220 to 260 | °C | |
| Mold temperature | 30.0 to 50.0 | °C | |
| Hold pressure | 30.0 to 60.0 | MPa | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |