| About |
|---|
| Clariant Nylon 6 PA-211X032 is a Polyamide 6 (Nylon 6) material. It is available in North America for extrusion or injection molding. Important attributes of Clariant Nylon 6 PA-211X032 are: Flame Rated Chemical Resistant Corrosion Resistant Flame Retardant Good Dimensional Stability Typical applications include: Wire & Cable Conveyors Hose/Tubing Medical/Healthcare Military Applications&& |
| Product Description | |
|---|---|
| Supplier | Clariant |
| Generic | PA6 |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Excellent Processability,Good flexibility,Good Dimensional Stability,Corrosion Resistant,Flame Characteristics,Solvent resistance,Homopolymer,Good coloring,HB |
| Availabilitys | North America |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.11 | g/cm³ | ASTM D792 |
| Shrinkage rate | |||
| MD：3.2 mm | 1.4 | % | ASTM D955 |
| Water absorption rate | |||
| 24hr | 2.2 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 3.2mm | 48 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 54.4 | ℃ | ASTM D648 |
| Linear coefficient of thermal expansion | |||
| MD | 1.1E-4 | 1/℃ | ASTM D696 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | HB | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| M-level | 60 | ASTM D785 | |
| tensile strength | 54.5 | MPa | ASTM D638 |
| Tensile strain | |||
| yield | 150 | % | ASTM D638 |
| Bending modulus | 1650 | MPa | ASTM D790 |
| bending strength | 68.9 | MPa | ASTM D790 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 79 | °C | |
| Drying time | 2.0 to 4.0 | hr | |
| Recommended maximum moisture content | 0.20 | % | |
| Barrel rear temperature | 249 to 274 | °C | |
| Barrel middle temperature | 249 to 274 | °C | |
| Barrel front temperature | 249 to 274 | °C | |
| Processing (melt) temperature | 254 to 271 | °C | |
| Melt temperature (target) | 266 | °C | |
| Mold temperature | 66 to 93 | °C | |
| Injection speed | 快速 | ||
| Back pressure | 0.345 to 0.689 | MPa | |
| Screw speed | 20 to 100 | rpm | |
| Cushion | 3.18 to 6.35 | mm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |