| About |
|---|
| POCAN® S7020 000000 PBT, non-reinforced, injection molding, extrusion, flame retardant, improved impact strength&&POCAN® S7020 000000 PBT, non-reinforced, injection molding, extrusion, flame retardant, improved impact strength&&POCAN® S7020 000000 PBT, non-reinforced, injection molding, extrusion, flame retardant, improved impact strength&& |
| Product Description | |
|---|---|
| Supplier | LANXESS |
| Generic | polybutylene terephthalate |
| Material Status | Commercial: Active |
| Features | Halogen free,Flame Characteristics,Low to no phosphorus content,V-2,V-0 |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.38 | g/cm³ | ISO 1183 |
| Apparent density | 0.80 | g/cm³ | ISO 60 |
| Melt Volume Rate | |||
| 270℃，5 kg | 50.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | ISO 294-4 | ||
| TD：250℃，2.0 mm | 1.8 | % | ISO 294-4 |
| TD：120℃，2.0 mm，2 hrs | 0.40 | % | ISO 294-4 |
| MD：250℃，2.0 mm | 1.8 | % | ISO 294-4 |
| MD：120℃，2.0 mm，2 hrs | 0.40 | % | ISO 294-4 |
| Water absorption rate | |||
| Saturation, 23 ℃ | 0.60 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 0.20 | % | ISO 62 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30℃ | < 10 | kJ/m² | ISO 179/1eA |
| 23℃ | < 10 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -30℃ | 110 | kJ/m² | ISO 179/1eU |
| 23℃ | No Break | ISO 179/1eU | |
| Impact strength of cantilever beam notch | ISO 180/1A | ||
| -40℃ | < 10 | kJ/m² | ISO 180-1A |
| -30℃ | < 10 | kJ/m² | ISO 180-1A |
| 23℃ | < 10 | kJ/m² | ISO 180-1A |
| Notched impact strength of cantilever beam | ISO 180/1U | ||
| -30℃ | 65 | kJ/m² | ISO 180/1U |
| 23℃ | No Break | ISO 180/1U | |
| Multi axial instrumented peak impact force | |||
| 23℃ | 80.0 | N | ISO 6603-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 65.0 | ℃ | ISO 75-2/A |
| 0.45 MPa, unannealed | 125 | ℃ | ISO 75-2/B |
| Vicat Softening Temp | |||
| B120 | 150 | ℃ | ISO 306/B120 |
| Ball pressure test | |||
| 190℃ | Pass | IEC 60695-10-2 | |
| Melting temperature | 225 | ℃ | ISO 11357-3 |
| Linear coefficient of thermal expansion | |||
| TD：23~55℃ | 1.1E-4 | 1/℃ | ISO 11359-2 |
| MD：23~55℃ | 1.1E-4 | 1/℃ | ISO 11359-2 |
| Thermal conductivity coefficient | |||
| 23℃ | 0.25 | W/m/K | ISO 8302 |
| Relative temperature index | |||
| Electrical performance | 125 | ℃ | UL 746 |
| Strength mechanical performance | 125 | ℃ | UL 746 |
| Impact mechanical performance | 115 | ℃ | UL 746 |
| Halving Interval | IEC 60216 | ||
| — | 5.3 | ℃ | IEC 60216 |
| — | 5.8 | ℃ | IEC 60216 |
| Temperature index | IEC 60216 | ||
| Dielectric strength | 135 | IEC 60216 | |
| 23 ℃，1 mm | 23 | kV/mm | IEC 60243-1 |
| Tensile impact strength | 120 | IEC 60216 | |
| tensile strength | 135 | IEC 60216 | |
| Yield, 23 ℃ | 45.0 | MPa | ISO 527-2/50 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | > 1.0E+15 | ohms | IEC 60093 |
| Volume resistivity | |||
| 23℃ | > 1.0E+17 | ohms·cm | IEC 60093 |
| Relative permittivity | IEC 60250 | ||
| 23℃，100 Hz | 3.80 | IEC 60250 | |
| 23℃，1 MHz | 3.60 | IEC 60250 | |
| Dissipation factor | IEC 60250 | ||
| 23℃，100 Hz | 4.0E-3 | IEC 60250 | |
| 23℃，1 MHz | 0.024 | IEC 60250 | |
| Compared to the leakage tracing index | |||
| Solution A | 600 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 0.80 mm | V-2 | UL 94 | |
| 1.50 mm | V-0 | UL 94 | |
| Glowing wire flammability index | |||
| 0.80 mm | 960 | ℃ | IEC 60695-2-12 |
| Extreme oxygen index | 30 | % | ISO 4589-2 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Electrolytic corrosion | A 1 | IEC 60426 | |
| ISO Shortname | PBT, GFHMPR, 11-020; ISO 1043-PBT FR (17) | ISO 7792 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 23℃ | 2300 | MPa | ISO 527-1-2 |
| Tensile strain | |||
| Yield, 23 ℃ | 4.5 | % | ISO 527-2/50 |
| Nominal tensile fracture strain | |||
| 23℃ | > 15 | % | ISO 527-2/50 |
| Tensile Creep Modulus（1 hr） | 2300 | MPa | ISO 899-1 |
| Tensile creep modulus | |||
| 1000 hr | 1600 | MPa | ISO 899-1 |
| Bending modulus | |||
| 23℃ | 2300 | MPa | ISO 178-A |
| bending strength | |||
| 3.50% strain | 70.0 | MPa | ISO 178-A |
| 23℃ | 75.0 | MPa | ISO 178 |
| Bending strain | 5.3 | % | |
| Ball hardness | 120 | MPa | ISO 2039-1 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature – Dehumidifying desiccant | 120 | °C | |
| Drying time – Dehumidifying desiccant | 4.0 to 8.0 | hr | |
| Processing (melt) temperature | 240 to 260 | °C | |
| Mold temperature | 80 to 100 | °C | |
| Residual Moisture Content | 0.0 to 0.020 | % | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 60x60x2mm, 4 hr |
| 3. 60x60x2mm, 80°C MT, 600 bar |
| 4. 0.079 in/min |
| 5. 2 mm/min |
| 6. 10°C/min |
| 7. Procedure A |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |