| About |
|---|
| Sarlink ML-1100 is a general purpose thermoplastic elastomer series, available in NAT and BLK designed for automotive interior applications. Sarlink ML-1150N NAT is a medium hardness, high density, filled grade suitable for injection molding.&& |
| Product Description | |
|---|---|
| Supplier | Teknor Apex |
| Generic | TPE |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Excellent Processability,Good flexibility,Low liquidity,Good bond,Elastic,Good tear strength,High density,Solvent resistance,Good coloring |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| elastic body | Nominal value | Unit | Test method |
| tensile strength | ISO 37 | ||
| TD, 100% strain | 1.13 | MPa | ISO 37 |
| MD, 100% strain | 1.60 | MPa | ISO 37 |
| Tensile strain | ISO 37 | ||
| fracture | 860 | % | ISO 37 |
| Flow rate, fracture | 740 | % | ISO 37 |
| tear strength | ISO 34-1 | ||
| TD | 20 | kN/m | ISO 34-1 |
| MD | 20 | kN/m | ISO 34-1 |
| Compression deformation | ISO 815 | ||
| 23℃，22 hr | 25 | % | ISO 815 |
| 70℃，22 hr | 43 | % | ISO 815 |
| 90℃，70 hr | 69 | % | ISO 815 |
| 125℃，70 hr | 93 | % | ISO 815 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ISO 868 | ||
| Shore A, 1 second, injection molding | 53 | ISO 868 | |
| Shore A, 5 seconds, injection molding | 51 | ISO 868 | |
| Shore A, 15 seconds, injection molding | 49 | ISO 868 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air | ISO 188 | ||
| TD：110℃，1008 hr | 8.2 | % | ISO 188 |
| MD：110℃，1008 hr | 14 | % | ISO 188 |
| TD: 100% strain at 110 ℃, 1008 hr | 2.7 | % | ISO 188 |
| MD: 100% strain at 110 ℃, 1008 hr | 3.8 | % | ISO 188 |
| TD：125℃，168 hr | 12 | % | ISO 188 |
| MD：125℃，168 hr | 14 | % | ISO 188 |
| TD: 100% strain 125 ℃, 168 hr | -0.88 | % | ISO 188 |
| MD: 100% strain 125 ℃, 168 hr | 13 | % | ISO 188 |
| Changes in tensile stress during fracture in air | ISO 188 | ||
| TD：110℃，1008 hr | 8.1 | % | ISO 188 |
| Flow rate: 110 ℃, 1008 hr | 12 | % | ISO 188 |
| TD：125℃，168 hr | 15 | % | ISO 188 |
| Flow rate: 125 ℃, 168 hr | 18 | % | ISO 188 |
| The rate of change of Shore hardness in air | ISO 188 | ||
| Shore A, 110 ℃, 1008 hr | 1.1 | ISO 188 | |
| Shore A, 110 ℃, 1008 hr | 1.3 | ISO 188 | |
| Shore A, 110 ℃, 1008 hr | 0.0 | ISO 188 | |
| Shaw A, 125 ℃, 168 hr | 1.5 | ISO 188 | |
| Shaw A, 125 ℃, 168 hr | 1.2 | ISO 188 | |
| Shaw A, 125 ℃, 168 hr | 0.80 | ISO 188 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.19 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 6.0 | g/10min | ASTM D1238 |
| Apparent viscosity of melt | |||
| 200℃，206 sec^-1 | 127 | Pa·s | ASTM D3835 |
| Special value | Nominal value | Unit | Test method |
|---|---|---|---|
| fracture | 4.90 | MPa | ISO 37 |
| MD, fracture | 4.30 | MPa | ISO 37 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Barrel rear temperature | 171 to 193 | °C | |
| Barrel middle temperature | 177 to 199 | °C | |
| Barrel front temperature | 182 to 204 | °C | |
| Nozzle temperature | 188 to 210 | °C | |
| Processing (melt) temperature | 188 to 210 | °C | |
| Mold temperature | 25 to 66 | °C | |
| Injection pressure | 1.38 to 6.89 | MPa | |
| Injection speed | Moderate-Fast | ||
| Back pressure | 0.172 to 0.345 | MPa | |
| Screw speed | 50 to 100 | rpm | |
| Cushion | 3.81 to 25.4 | mm | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Type 1, 20 in/min |
| 3. Method Ba, Angle (Unnicked), 20 in/min |
| 4. Type A |
| 5. Type 1 |
| 6. 5 sec |
| 7. 15 sec |
| 8. 1 sec |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |