| About |
|---|
| RX® 640 is a fiberglass reinforced, ammonia-free, phenolic resole compound, with good dimensional stability and good strength at elevated temperatures. Meets ASTM D-5948 Type GPI-5.&& |
| Product Description | |
|---|---|
| Supplier | SBHPP |
| Generic | 酚醛树脂 |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good Dimensional Stability,V-0 |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.76 | g/cm³ | ASTM D792 |
| Apparent density | 0.80 | g/cm³ | ASTM D1895 |
| Shrinkage rate | |||
| MD | 0.20 | % | ASTM D955 |
| Water absorption rate | |||
| 48hr | 0.22 | % | ASTM D570 |
| 24hr | 0.060 | % | ASTM D570 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 40 | J/m | ASTM D256-A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | ASTM D648A | ||
| 1.8 MPa, unannealed | 280 | ℃ | ASTM D648-A |
| 1.8 MPa, annealed | > 282 | ℃ | ASTM D648-A |
| Linear coefficient of thermal expansion | |||
| MD | 1.4E-5 | 1/℃ | ASTM E831 |
| Thermal conductivity coefficient | 0.55 | W/m/K | ASTM C518 |
| Relative temperature index | 150 | ℃ | UL 746 |
| Electrical performance | 150 | ℃ | UL 746 |
| Impact mechanical performance | 150 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | ASTM D149 | ||
| — | 14 | kV/mm | ASTM D149 |
| — | 12 | kV/mm | ASTM D149 |
| Arc resistance | 160 | sec | ASTM D495 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.60 mm | V-0 | UL 94 | |
| 3.20 mm | V-0 | UL 94 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Rockwell hardness | |||
| E-level | 90 | ASTM D785 | |
| tensile strength | 86.0 | MPa | ASTM D638 |
| Bending modulus | 14500 | MPa | ASTM D790 |
| bending strength | 186 | MPa | ASTM D790 |
| compressive strength | 248 | MPa | ASTM D695 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Dry, 60 Hz |
| 3. Method A (Short-Time) |
| 4. Method B (Step-by-Step) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |