| About |
|---|
| 60 Shore A TPE (Styrenic Block Copolymer/PP based), available in black and natural. This grade is economical, offers good processability, aesthetics and intermediate heat resistance.&& |
| Product Description | |
|---|---|
| Generic | TPE |
| Material Status | Commercial: Negative |
| Features | Weather resistance is good,Excellent Processability,Alkali resistant,Good surface appearance,High elastic,Renewable resources,Ethanol tolerance,Acidproof,Good bond,Grease resistance,Ozone resistance,Heat Resistance, Good,Solvent resistance,Good coloring,Resistance to detergents |
| Availabilitys | North America |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.15 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 8.0 | g/10min | ASTM D1238 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | ASTM D2240 | ||
| Shore A, 10 seconds, extrusion molding | 57 | ASTM D2240 | |
| Shore A, 10 seconds, injection molding | 60 | ASTM D2240 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| fracture | 5.69 | MPa | ASTM D412 |
| 100% strain | 1.73 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 780 | % | ASTM D412 |
| tear strength | 24.9 | kN/m | ASTM D624 |
| Compression deformation | ASTM D395B | ||
| 23℃，22 hr | 19 | % | ASTM D395B |
| 70℃，22 hr | 42 | % | ASTM D395B |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -60.0 | ℃ | ASTM D746 |
| Dynamic Service Temperature | 90 | ℃ |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Drying temperature | 66 to 71 | °C | |
| Drying time | 2.0 to 3.0 | hr | |
| Barrel rear temperature | 171 to 199 | °C | |
| Barrel middle temperature | 177 to 210 | °C | |
| Barrel front temperature | 191 to 221 | °C | |
| Nozzle temperature | 199 to 229 | °C | |
| Processing (melt) temperature | 199 to 221 | °C | |
| Mold temperature | 10 to 49 | °C | |
| Injection pressure | 5.17 to 8.96 | MPa | |
| Drying temperature | 66 to 71 | °C | |
| Drying time | 2.0 to 3.0 | hr | |
| Barrel temperature | 160 to 177 | °C | |
| Barrel 1 zone temperature | 171 to 191 | °C | |
| Barrel 3 zone temperature | 179 to 199 | °C | |
| Barrel 5 zone temperature | 191 to 210 | °C | |
| Connector temperature | 191 to 210 | °C | |
| Melt temperature | 191 to 199 | °C | |
| Nozzle temperature | 191 to 210 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |