| About |
|---|
| NORYL RN0611 is an unfilled Post Consumer recycle (PCR) based injection moldable modified polyphenylene ether resin comprising at least 30% PCR styrenic series resin content. Designed for good dimensional stability and high flow, this resin also uses non-chlorinated, non-brominated FR additives with a specific density of 1.1 g/cm^3. NORYL RN0611 may be an excellent material candidate for flat panel TV enclosure applications requiring good rheological properties, heat resistance, hydrolysis resistance and low density.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PPO(PPE)+PS |
| Material Status | Commercial: Active |
| Features | Good Dimensional Stability,High liquidity,Hydrolysis stability,Halogen free,Flame Characteristics,High Heat Resistance,Low density,V-1 |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.11 | g/cm³ | ASTM D792, ISO 1183 |
| Melt Volume Rate | ISO 1133 | ||
| 300℃，1.2 kg | 17.0 | cm³/10min | |
| 280℃，2.16 kg | 35.0 | cm³/10min | |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| — | 2300 | MPa | ASTM D638 |
| — | 2200 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 47.0 | MPa | ASTM D638 |
| yield | 46.0 | MPa | ISO 527-2/50 |
| fracture | 46.0 | MPa | ASTM D638 |
| fracture | 45.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| yield | 3.0 | % | ASTM D638 |
| yield | 3.0 | % | ISO 527-2/50 |
| fracture | 5.0 | % | ASTM D638 |
| fracture | 6.0 | % | ISO 527-2/50 |
| Bending modulus | |||
| 50 mm span | 2300 | MPa | ASTM D790 |
| — | 2200 | MPa | ISO 178 |
| bending strength | |||
| — | 71.0 | MPa | ISO 178 |
| Yield, 50 mm span | 78.0 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30℃ | 4.0 | kJ/m² | |
| 23℃ | 5.0 | kJ/m² | |
| Impact strength of cantilever beam notch | |||
| -30℃ | 30 | J/m | ASTM D256 |
| 23℃ | 38 | J/m | ASTM D256 |
| -30℃ | 3.0 | kJ/m² | ISO 180-1A |
| 23℃ | 5.0 | kJ/m² | ISO 180-1A |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed, 3.2 mm | 93.0 | ℃ | ASTM D648 |
| 0.45 MPa, unannealed, 64 mm span | 94.0 | ℃ | ISO 75-2/Bf |
| 1.8 MPa, unannealed, 64 mm span | 77.0 | ℃ | ISO 75-2/Af |
| 1.8 MPa, annealed, 3.2 mm | 80.0 | ℃ | ASTM D648 |
| Vicat Softening Temp | |||
| B50 | 99.0 | ℃ | ASTM D1525, ISO 306/B50 10 14 |
| B120 | 101 | ℃ | ISO 306/B120 |
| Linear coefficient of thermal expansion | ASTM E831, ISO 11359-2 | ||
| MD：-40~40℃ | 7.7E-5 | 1/℃ | |
| TD：-40~40℃ | 7.9E-5 | 1/℃ | |
| Relative temperature index | 65.0 | ℃ | UL 746 |
| Electrical performance | 65.0 | ℃ | UL 746 |
| Impact mechanical performance | 65.0 | ℃ | UL 746 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric constant | |||
| 1 MHz | 2.70 | ASTM D150，IEC 60250 | |
| Dissipation factor | |||
| 1 MHz | 2.9E-3 | ASTM D150，IEC 60250 | |
| Hot wire ignition | |||
| HWI | PLC 1 | UL 746 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.50 mm | V-1 | UL 94 | |
| Extreme oxygen index | 30 | % | ISO 4589-2 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 70.0 to 80.0 | °C | |
| Drying time | 2.0 to 3.0 | hr | |
| Hopper temperature | 65.0 to 85.0 | °C | |
| Barrel rear temperature | 210 to 230 | °C | |
| Barrel middle temperature | 240 to 270 | °C | |
| Barrel front temperature | 260 to 295 | °C | |
| Nozzle temperature | 250 to 280 | °C | |
| Processing (melt) temperature | 260 to 295 | °C | |
| Mold temperature | 45.0 to 70.0 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 3. 0.051 in/min |
| 4. 0.079 in/min |
| 5. at Yield |
| 6. 80*10*4 sp=62mm |
| 7. 80*10*4 mm |
| 8. Rate A (50°C/h), Loading 2 (50 N) |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |