| About |
|---|
| Moplen EP300L is the polypropylene block copolymer manufactured by PMC under the license of BASELL using the Spheripol process. Moplen EP300L is a block copolymer selected by customers for use in injection molding of toys, crates, battery case. Moplen EP300L resin meets the FDA requirements in the Code of Federal Regulations in 21 CFR 177.1520 for food contact. Moplen EP300L has a flame rating of UL94HB.&& |
| Product Description | |
|---|---|
| Supplier | LyondellBasell |
| Generic | PP copolymer |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Low warping,Good flexibility,Food contact compliance,Block Copolymer,low-temperature impact resistance |
| Availabilitys | Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.900 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 6.0 | g/10min | ISO 1133 |
| Melt Volume Rate | |||
| 230℃，2.16 kg | 8.00 | cm³/10min | ISO 1133 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -20℃ | 3.0 | kJ/m² | ISO 179/1eA |
| 0℃ | 4.0 | kJ/m² | ISO 179/1eA |
| 23℃ | 7.5 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -20℃ | 110 | kJ/m² | ISO 179/1eU |
| 0℃ | 160 | kJ/m² | ISO 179/1eU |
| 23℃ | No Break | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 77.0 | ℃ | ISO 75-2/B |
| Toughness/brittle transition temperature | -47.0 | ℃ | ISO 6603-2 |
| Vicat Softening Temp | |||
| A50 | 151 | ℃ | ISO 306/A50 |
| B50 | 66.0 | ℃ | ISO 306 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 60° | 83 | DIN 67530 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 1250 | MPa | ISO 527-2 |
| tensile strength | |||
| yield | 26.0 | MPa | ISO 527-2 |
| Tensile strain | |||
| fracture | > 50 | % | ISO 527-2 |
| yield | 8.0 | % | ISO 527-2 |
| Ball hardness | |||
| H358/30 | 53.0 | MPa | ISO 2039-1 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |