| About |
|---|
| SABIC® STAMAX 40YM240E is a 40% long glass fiber reinforced low emission grade. The glass fibres are chemically coupled to the PP matrix, resulting in high stiffness and strength.&& |
| Product Description | |
|---|---|
| Supplier | SABIC |
| Generic | PP not specified |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Low odor,Chemical coupling |
| Availabilitys | Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.22 | g/cm³ | ISO 1183 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | ISO 527-2/1B | ||
| 23 ℃, injection molding | 8300 | MPa | ISO 527-2/1B |
| 80 ℃, injection molding | 5700 | MPa | ISO 527-2/1B |
| 120 ℃, injection molding | 4500 | MPa | ISO 527-2/1B |
| tensile strength | ISO 527-2/1B | ||
| 23 ℃, injection molding | 121 | MPa | ISO 527-2/1B |
| 80 ℃, injection molding | 75.0 | MPa | ISO 527-2/1B |
| Tensile strain | |||
| Fracture, 23 ℃, injection molding | 2.1 | % | ISO 527-2/1B |
| Bending modulus | ISO 178 | ||
| 23 ℃, injection molding | 7850 | MPa | ISO 178 |
| 80 ℃, injection molding | 5550 | MPa | ISO 178 |
| bending strength | ISO 178 | ||
| 23 ℃, injection molding | 172 | MPa | ISO 178 |
| 80 ℃, injection molding | 91.0 | MPa | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -30 ℃, injection molding | 28 | kJ/m² | ISO 179/1eA |
| 23 ℃, injection molding | 22 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -30 ℃, injection molding | 48 | kJ/m² | ISO 179/1eU |
| 23 ℃, injection molding | 68 | kJ/m² | ISO 179/1eU |
| Falling target impact | |||
| Total Energy，23℃ | 66.0 | J/cm | ISO 6603-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 157 | ℃ | ISO 75-2/A |
| Linear coefficient of thermal expansion | |||
| MD | ASTM D696 | ||
| -30 to 30 ℃ | 4.4E-5 | cm/cm/℃ | ASTM D696 |
| 23 to 80 ℃ | 3.1E-5 | cm/cm/℃ | ASTM D696 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Injection Molded |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |