| About |
|---|
| ULTRATRAC H950 meets or exceeds all requirements for NEMA GPO-3 type material. ULTRATRAC H950 is recognized by UL as a 94 V-O material and offers great arc protection (UL FILE E81893). Testing at an independent laboratory shows ULTRATRAC Grade H950 to be non-toxic as defined by Military Specification MIL M-14H. Excellent flame resistance and very low smoke generation is also characteristic of this material. Available thicknesses – .093″ – 2.00″. Standard color – Red. Meets Gov’t Spec – I-24768/6.&& |
| Product Description | |
|---|---|
| Generic | 热固性聚酯 |
| Material Status | Commercial: Active |
| Features | Low smoke,Flame Characteristics,Nontoxicity,V-0 |
| Availabilitys | North America |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.80 | g/cm³ | ASTM D792 |
| Water absorption rate | |||
| balance | 0.20 | % | ASTM D229 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | 510 | J/m | ASTM D256 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | |||
| StepByStep in oil | 55000 | V | ASTM D149 |
| 1.59 mm in oil | 21 | kV/mm | ASTM D149 |
| Dielectric constant | |||
| 60 Hz | 5.20 | ASTM D150 | |
| Dissipation factor | |||
| 60 Hz | 0.060 | ASTM D150 | |
| Arc resistance | 194 | sec | ASTM D495 |
| Compared to the leakage tracing index | > 600 | V | |
| Inclined（Plane Tracking） | > 1000 | min | ASTM D2303 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | V-0 | UL 94 | |
| Flame Resistance | ASTM D229 | ||
| Burning Time | 33.0 | sec | ASTM D229 |
| Ignition time | 130.0 | sec | ASTM D229 |
| Radiation Plate Listing (UL) – Flame Propagation | 5.00 | ASTM E162 | |
| Smoke density | |||
| at 4.0 minutes，flaming | 0.0 | ASTM E662 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Bond Strength（1.27 cm） | 9.65 | MPa | ASTM D229 |
| Temperature level | 160 | ℃ | |
| Tunnel Test (flame propagation, 6.35 mm) | < 25.0 | ASTM E84 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Babbitt hardness | 62 | ||
| tensile strength | 75.8 | MPa | ASTM D638 |
| Bending modulus | 10300 | MPa | ASTM D790 |
| bending strength | 172 | MPa | ASTM D790 |
| compressive strength | 207 | MPa | ASTM D695 |
| shear strength | 96.5 | MPa | ASTM D732 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Method A (Short-Time) |
| 3. Perpendicular |
| 4. Parallel |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |