Hanwha Total PP CH53W

About
CH53W is a polypropylyene compound with ultra-weatherability, ideal for use in outdoor products/components such as the exteriors of air conditioners. This grade is polypropylene with a CaCO3 inorganic filler, so rigidity and heat resistance have been improved. This product is manufactured with a variety of base PPs, including HIPP (High Isotactic Polypropylene), using HANWHA TOTAL’s special processing technologies. CH53W offers excellent rigidity and impact-resistance in good balance. Additional features include excellent long-term heat-resistance, high resistance to discoloration, antistatic property and dimensional stability.&&

About

CH53W is a polypropylyene compound with ultra-weatherability, ideal for use in outdoor products/components such as the exteriors of air conditioners. This grade is polypropylene with a CaCO3 inorganic filler, so rigidity and heat resistance have been improved. This product is manufactured with a variety of base PPs, including HIPP (High Isotactic Polypropylene), using HANWHA TOTAL’s special processing technologies. CH53W offers excellent rigidity and impact-resistance in good balance. Additional features include excellent long-term heat-resistance, high resistance to discoloration, antistatic property and dimensional stability.&&

Product Description
Supplier	HANWHA
Generic	HC PP
Material Status	Commercial: Active
Features	Good Rigidity,Weather resistance is good,Excellent Processability,High impact resistance,Good Dimensional Stability,High Heat Resistance,Antistatic property
Availabilitys	North America,Asia Pacific
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.09	g/cm³	ASTM D1505
Melt Flow Rate
230℃，2.16kg	12	g/10min	ASTM D1238
Shrinkage rate
MD：2.0 mm	1.0 to 1.4	%	ASTM D955

IMPACT	Nominal value	Unit	Test method
Impact strength of cantilever beam notch
23℃	44	J/m	ASTM D256

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	127	℃	ASTM D648

MECHANICAL	Nominal value	Unit	Test method
Rockwell hardness
R-level	100		ASTM D785
tensile strength	31.4	MPa	ASTM D638
Tensile strain
fracture	30	%	ASTM D638
Bending modulus
23℃	53.9	MPa	ASTM D747
Bending modulus	2550	MPa	ASTM D790

Process Conditions
injection	Nominal value	Unit	Test method
Barrel rear temperature	180 to 200	°C
Barrel middle temperature	190 to 210	°C
Barrel front temperature	200 to 220	°C
Mold temperature	40 to 80	°C
Injection pressure	58.8 to 98.1	MPa
Hold pressure	39.2 to 88.3	MPa
Screw speed	30 to 80	rpm

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.