| About |
|---|
| By selecting specific monomers, one can achieve a crystallizable and permanently transparent polyamide: TROGAMID® CX. The crystallites are so small that they do not scatter visible light, and the material appears transparent to the human eye—a property known as microcrystallinity. Because of its crystallinity, the microcrystalline structure retains important properties such as stress cracking resistance — without clouding. The degree of crystallinity is so negligible, however, that it has no adverse effect on the shrinkage behavior of molded parts. TROGAMID® CX undergoes a similar isotropic shrinkage like amorphous materials. The combination of good UV resistance, high mechanical strength, permanent transparency, high transmission and superior chemical resistance opens a wide range of applications for TROGAMID® CX. Typical areas of application are in the automotive industry, machinery and engineering, medical technology, the sports and recreation industry, the glasses production, the cosmetics industry and in water treatment and filter technology. TROGAMID® CX9704: Low-viscous, permanently transparent polyamide for injection molding&& |
| Product Description | |
|---|---|
| Supplier | Evonik |
| Generic | PA12 |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Weather resistance is good,Excellent Processability,Good Clarity,High impact resistance,Good Dimensional Stability,Low or no water absorption,Low Viscosity,Low contractility,Good wear resistance,Solvent resistance,low-temperature impact resistance,High scratch resistance,High ESCR |
| Availabilitys | North America,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.02 | g/cm³ | ISO 1183 |
| Viscosity number | > 120 | cm³/g | ISO 307 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| -30 ℃, completely fractured | 10 | kJ/m² | |
| 0 ℃, completely fractured | 11 | kJ/m² | |
| 23 ℃, completely fractured | 11 | kJ/m² | |
| Charpy Unnotch Impact strength | |||
| -30℃ | 无断裂 | ||
| 0℃ | 无断裂 | ||
| 23℃ | 无断裂 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 120 | ℃ | ISO 75-2/B |
| 1.8 MPa, unannealed | 102 | ℃ | ISO 75-2/A |
| Glass transition temperature | 132 | ℃ | ISO 11357-2 |
| Vicat Softening Temp | |||
| — | 132 | ℃ | ISO 306/A |
| — | 125 | ℃ | ISO 306/B |
| Linear coefficient of thermal expansion | |||
| MD：23~55℃ | 9.0E-5 | 1/℃ | |
| TD：23~55℃ | 9.0E-5 | 1/℃ |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Surface resistivity | 1.0E+14 | ohms | IEC 60093 |
| Volume resistivity | 1.0E+15 | ohms·cm | IEC 60093 |
| Relative permittivity | |||
| 23℃，100 Hz | 3.40 | ||
| 23℃，1 MHz | 3.30 | ||
| Dissipation factor | |||
| 23℃，100 Hz | 0.013 | ||
| 23℃，1 MHz | 0.022 | ||
| Compared to the leakage tracing index | |||
| CTI | 575 | V | |
| Solution A | 600 | V |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 0.80 mm | HB | ||
| 1.60 mm | HB | ||
| Glowing wire flammability index | |||
| 1.0 mm | 960 | ℃ | IEC 60695-2-12 |
| Igniting temperature of the hot wire | |||
| 1 mm | 825 | ℃ | IEC 60695-2-13 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw’s D | 81 | ISO 868 | |
| Ball hardness | 110 | MPa | ISO 2039-1 |
| Tensile modulus | |||
| 23℃ | 1400 | MPa | ISO 527-2 |
| tensile strength | |||
| Yield, 23 ℃ | 60.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| Yield, 23 ℃ | 8.0 | % | ISO 527-2/50 |
| Nominal tensile fracture strain | |||
| 23℃ | > 50 | % | ISO 527-2/50 |
| Bending modulus | 1500 | MPa | ISO 178 |
| bending strength | |||
| — | 90.0 | MPa | |
| 3.50% strain | 50.0 | MPa | |
| Outer Fiber Strain（at maximum stress） | > 10 | % | ISO 178 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.20 in/min |
| 3. 5.0 mm/min |
| 4. 10 K/min |
| 5. 100 drops value |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |