| About |
|---|
| Bormed SC820CF-11 is a soft random heterophasic copolymer. This grade is suitable for the manufacturing of non-oriented cast films on chill roll process and blown film on tubular water quenching process. CAS-No.: 9010-79-1 Applications Bormed SC820CF-11 has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed SC820CF-11 . Medical device packaging Pouches for IV solutions Pouches for Continuous Ambulatory Peritoneal Dialysis Secondary packaging This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special features High gloss High toughness at low temperatures High softness Sterilisability by means of water steam Low haze High water vapour barrier High impact strength at 23 °C&& |
| Product Description | |
|---|---|
| Supplier | Borealis AG |
| Generic | PP copolymer |
| Material Status | Commercial: Active |
| Features | Good Clarity,Good flexibility,Good surface appearance,High impact resistance,Steam sterilized,Renewable resources,Moisture resistance,Random copolymer,Low temperature toughness,Soft |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Melt Flow Rate | |||
| 230℃，2.16kg | 3.9 | g/10min | ISO 1133 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Bending modulus | |||
| injection molding | 550 | MPa | ISO 178 |
| friction coefficient | |||
| Casting thin film | > 0.70 | ISO 8295 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| MD, 50 µ m, cast thin film | 330 | MPa | |
| TD, 50 µ m, cast thin film | 330 | MPa | |
| tensile strength | |||
| MD, 50 µ m, blow molded film | 50.0 | MPa | |
| TD, 50 µ m, blow molded film | 50.0 | MPa | |
| Tensile strain | |||
| MD, fracture, 50 µ m, cast thin film | 650 | % | |
| TD, fracture, 50 µ m, cast thin film | 670 | % | |
| Instrumented Puncture Test（Total Penetration Energy，50.0 µm） | 300 | J/cm | ISO 7765-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | 141 | ℃ | ISO 11357-3 |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 20 °, 50 µ m, cast thin film | > 120 | ASTM D2457 | |
| Haze | |||
| 50 µ m, cast thin film | < 1.0 | % | ASTM D1003 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Cast Film |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |