| About |
|---|
| Normal viscosity, heat stabilised polyester PET, 30% glass fiber reinforced&& |
| Product Description | |
|---|---|
| Generic | PET |
| Material Status | Commercial: Active |
| Features | Heat Stabilized,HB |
| Availabilitys | North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.56 | g/cm³ | ISO 1183 |
| Shrinkage rate | ISO 294-4 | ||
| TD | 0.80 | % | ISO 294-4 |
| MD | 0.40 | % | ISO 294-4 |
| Water absorption rate | ISO 62 | ||
| Saturation, 23 ℃ | 0.50 | % | ISO 62 |
| Equilibrium, 23 ℃, 50% RH | 0.18 | % | ISO 62 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 11400 | MPa | ISO 527-1-2 |
| tensile strength | |||
| fracture | 155 | MPa | ISO 527-2/5 |
| Tensile strain | |||
| fracture | 2.1 | % | ISO 527-2/5 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | |||
| 23℃ | 10 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | |||
| 23℃ | 45 | kJ/m² | ISO 179/1eU |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed | 245 | ℃ | ISO 75-2/B |
| 1.8 MPa, unannealed | 225 | ℃ | ISO 75-2/A |
| Melting temperature | 255 | ℃ | ISO 11357-3 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | 32 | kV/mm | IEC 60243-1 |
| Dielectric constant | |||
| 1 MHz | 3.90 | IEC 60250 | |
| Compared to the leakage tracing index | 250 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | UL 94 | ||
| 1.60 mm | HB | UL 94 | |
| 3.20 mm | HB | UL 94 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| ISO Shortname | PET, MPRMC, 13-110; GF30 | ISO 1874 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Drying temperature | 90 | °C | |
| Drying time | 4.0 | hr | |
| Recommended maximum moisture content | 0.0 to 0.050 | % | |
| Proposed maximum recycled material ratio | 20 | % | |
| Barrel rear temperature | 265 to 290 | °C | |
| Barrel middle temperature | 275 to 300 | °C | |
| Barrel front temperature | 280 to 290 | °C | |
| Processing (melt) temperature | 270 to 300 | °C | |
| Mold temperature | 120 to 140 | °C | |
| Injection pressure | 78.0 | MPa | |
| Screw length to diameter ratio | 18.0:1.0 to 22.0:1.0 | ||
| Screw compression ratio | 2.2:1.0 to 2.8:1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |