| About |
|---|
| PC+ASA-Blend; Vicat/B 120 temperature = 115°C; UV-stabilized; very good surface finish&& |
| Product Description | |
|---|---|
| Supplier | Covestro |
| Generic | ASA+PC |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Good surface appearance |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.14 | g/cm³ | ISO 1183 |
| Melt Volume Rate | |||
| 260℃，5 kg | 34.0 | cm³/10min | ISO 1133 |
| Shrinkage rate | ISO 2577 | ||
| TD：2.0 mm | 0.50 to 0.70 | % | ISO 2577 |
| MD：2.0 mm | 0.50 to 0.70 | % | ISO 2577 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 23℃ | 2830 | MPa | ISO 527-1-2 |
| tensile strength | |||
| Fracture, 23 ℃ | 50.0 | MPa | ISO 527-2/50 |
| Yield, 23 ℃ | 65.0 | MPa | ISO 527-2/50 |
| Tensile strain | |||
| Fracture, 23 ℃ | 50 | % | ISO 527-2/50 |
| Yield, 23 ℃ | 4.0 | % | ISO 527-2/50 |
| Bending modulus | |||
| 23℃ | 2840 | MPa | ISO 178 |
| bending strength | |||
| 3.50% strain, 23 ℃ | 85.0 | MPa | ISO 178 |
| Bending strain | 5.0 | % | ISO 178 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | ISO 180/A | ||
| -30℃ | 7.0 | kJ/m² | ISO 180-A |
| 23℃ | 14 | kJ/m² | ISO 180-A |
| Multi axial instrumented impact energy | ISO 6603-2 | ||
| -30℃ | 20.0 | J | ISO 6603-2 |
| 23℃ | 45.0 | J | ISO 6603-2 |
| Multi axial instrumented peak impact force | ISO 6603-2 | ||
| -30℃ | 4250 | N | ISO 6603-2 |
| 23℃ | 4800 | N | ISO 6603-2 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 93.0 | ℃ | ISO 75-2/A |
| 0.45 MPa, unannealed | 112 | ℃ | ISO 75-2/B |
| Vicat Softening Temp | |||
| B50 | 113 | ℃ | ISO 306 |
| B120 | 115 | ℃ | ISO 306/B120 |
| Linear coefficient of thermal expansion | |||
| TD：23~55℃ | 7.0E-5 | 1/℃ | ISO 11359-2 |
| MD：23~55℃ | 7.0E-5 | 1/℃ | ISO 11359-2 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 60x60x2mm |
| 3. 0.079 in/min |
| 4. 2 mm/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |