| About |
|---|
| CERTENE™ PHM-20AN PHM-20AN is a certified prime grade Nucleated Polypropylene designed for injection molding of thin-walled lightweight articles. PHM-20AN contains antistatic and combines a good balance of medium-high flow processability with high contact clarity, good tensile strength, high stiffness, short cycling, and excellent ESCR. PHM-20AN applications include lightweight containers, medical ware, caps, closures, and housewares. PHM-20AN recommended processing temperature is between 220° to 240°C with mold at 20°-50°C. PHM-20AN complies with FDA regulation 21CFR 177.1520 and with most international regulations concerning the use of Polypropylene in contact with food.&&CERTENE™ PHM-20AN PHM-20AN is a certified prime grade Nucleated Polypropylene designed for injection molding of thin-walled lightweight articles. PHM-20AN contains antistatic and combines a good balance of medium-high flow processability with high contact clarity, good tensile strength, high stiffness, short cycling, and excellent ESCR. PHM-20AN applications include lightweight containers, medical ware, caps, closures, and housewares. PHM-20AN recommended processing temperature is between 220° to 240°C with mold at 20°-50°C. PHM-20AN complies with FDA regulation 21CFR 177.1520 and with most international regulations concerning the use of Polypropylene in contact with food.&& |
| Product Description | |
|---|---|
| Generic | PP homopolymerization |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Excellent Processability,Good Clarity,High liquidity,Nucleation,Quick molding cycle,Food contact compliance,Good Tensile Strength,Antistatic property,High ESCR,Homopolymer |
| Availabilitys | North America |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.905 | g/cm³ | ASTM D1505 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 20 | g/10min | ASTM D1238 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23 ℃, injection molding | 32 | J/m | ASTM D256 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 0.45 MPa, unannealed, injection molded | 123 | ℃ | ASTM D648 |
| Vicat Softening Temp | 154 | ℃ | ASTM D1525 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| Yield, injection molding | 37.2 | MPa | ASTM D638 |
| Tensile strain | |||
| Yield, injection molding | 11 | % | ASTM D638 |
| Bending modulus | |||
| 1% cut, injection molding | 1860 | MPa | ASTM D790 |
| Rockwell hardness | |||
| R-level | 96 | ASTM D785 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Processing (melt) temperature | 104 to 116 | °C | |
| Mold temperature | -7 to 10 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 2.0 in/min |
| 3. 0.051 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |