AEI SX522A:CM401 and SX522A:CM401CDS

About
Ambient cure, silane crosslinkable polyethylene for low voltage power cable insulation This crosslinkable polyethylene compound is designed for the insulation of power cables; possessing outstanding extrusion properties at high output rates. The graft component SX522A is mixed with the crosslinking catalyst masterbatch CM401 generally in the ratio 95:5. It exhibits minimum point and die drool, low scorch characteristics and high production efficiency. It can be cured in ambient conditions and is specifically designed for small and sector shaped conductors.&&

About

Ambient cure, silane crosslinkable polyethylene for low voltage power cable insulation This crosslinkable polyethylene compound is designed for the insulation of power cables; possessing outstanding extrusion properties at high output rates. The graft component SX522A is mixed with the crosslinking catalyst masterbatch CM401 generally in the ratio 95:5. It exhibits minimum point and die drool, low scorch characteristics and high production efficiency. It can be cured in ambient conditions and is specifically designed for small and sector shaped conductors.&&

Product Description
Generic	LDPE
Material Status	Commercial: Active
Features	Crosslinked
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.920	g/cm³	BS 2782 620A
Melt Flow Rate
190℃，2.16kg	1.0	g/10min	Internal Method

MECHANICAL	Nominal value	Unit	Test method
tensile strength	18.0	MPa	IEC 60811-1-1
Tensile strain
fracture	450	%	IEC 60811-1-1

Aging performance	Nominal value	Unit	Test method
The rate of change in tensile strength
135℃，168 hr	7.0	%	IEC 60811-1-2
Changes in tensile stress during fracture
135℃，168 hr	-7.0	%	IEC 60811-1-2

THERMAL	Nominal value	Unit	Test method
Low temperature bending
-70℃	pass		IEC 60811-1-4
thermosetting			IEC 60811-2-1
Elongation under load: 20 N/cm ²， 200 ℃	< 100	%	IEC 60811-2-1
Maximum permanent elongation after cooling	0.0	%	IEC 60811-2-1

Electrical performance	Nominal value	Unit	Test method
Volume resistivity
20 ℃	> 1.0E+16	ohms·cm	BS 6622
Dielectric strength
20 ℃	21	kV/mm	IEC 60243-1
Relative permittivity
23℃，50 Hz	2.00		IEC 60250
power factor
50Hz，23℃	3.00E-4		IEC 60250

Supplementary information	Nominal value	Unit
Curing time –<100% high-temperature elongation
800.0 µm	5.0	day
1.50 mm	14.0	day

Process Conditions
Extrusion	Nominal value	Unit	Test method
Barrel 1 zone temperature	130	°C
Barrel 2 zone temperature	150	°C
Barrel 3 zone temperature	170	°C
Barrel 4 zone temperature	190	°C
Head temperature	200	°C
Nozzle temperature	210	°C

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.