FINGERPRINT™ DFDC-7525 NT

About
FINGERPRINT™ DFDC-7525 NT is a medium density polyethylene resin produced using Unipol™ process technology. It is intended for use in thin-wall micro irrigation tape applications and profile extrusion applications. DFDC-7525 NT exhibits good draw down characteristics producing tape with a reliable balance of extrusion ease and toughness. It also has utility as a blending component to modify and improve the physical properties of high pressure, very low density, linear low density, or high density polyethylene resins. Outdoor applications require the addition of UV stabilizer to maintain the excellent properties over extended periods of UV exposure. Dow DFNF-0092 carbon black masterbatch at a 6.5% concentration has been found to offer suitable UV resistance. Main Characteristics: High tensile properties High elongation properties Excellent burst strength Slip Additive: none Antiblock Additive: none Industrial Standards Compliance: ASTM D 3350: cell classification PE234510A&&

About

FINGERPRINT™ DFDC-7525 NT is a medium density polyethylene resin produced using Unipol™ process technology. It is intended for use in thin-wall micro irrigation tape applications and profile extrusion applications. DFDC-7525 NT exhibits good draw down characteristics producing tape with a reliable balance of extrusion ease and toughness. It also has utility as a blending component to modify and improve the physical properties of high pressure, very low density, linear low density, or high density polyethylene resins. Outdoor applications require the addition of UV stabilizer to maintain the excellent properties over extended periods of UV exposure. Dow DFNF-0092 carbon black masterbatch at a 6.5% concentration has been found to offer suitable UV resistance. Main Characteristics: High tensile properties High elongation properties Excellent burst strength Slip Additive: none Antiblock Additive: none Industrial Standards Compliance: ASTM D 3350: cell classification PE234510A&&

Product Description
Supplier	DOW
Generic	MDPE
Material Status	Commercial: Active
Availabilitys	North America,Latin America,Asia Pacific,Europe
Process Methods	Profile extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.939	g/cm³	ASTM D792
Melt Flow Rate			ASTM D1238
190℃，2.16kg	> 0.15	g/10min	ASTM D1238
190℃，21.6kg	20	g/10min	ASTM D1238
ESCR(Environmental Stress Cracking Resistance)
F0	> 2000	hr	ASTM D1693A

THERMAL	Nominal value	Unit	Test method
Embrittlement temperature	< -100	℃	ASTM D746A
Vicat Softening Temp	116	℃	ASTM D1525
Melting temperature
DSC	125	℃	Internal Method

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D	55		ASTM D2240
tensile strength			ASTM D638
yield	26.2	MPa	ASTM D638
fracture	30.0	MPa	ASTM D638
Tensile strain
fracture	> 800	%	ASTM D638
Bending modulus	689	MPa	ASTM D790

Process Conditions
Extrusion	Nominal value	Unit	Test method
Melt temperature	221 to 249	°C

Notes
1. Typical properties: these are not to be construed as specifications.
2. Compression molded parts prepared according to ASTM D 1928 Procedure C. Properties will vary with changes in molding conditions and aging time.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.