CONTINUUM™ DMDC-1250 NT 7

About
CONTINUUM™ DMDC-1250 NT 7 High Density Polyethylene Resin (HDPE) is intended for use in both compression and injection molded closure applications including carbonated soft drink and hot fill closures. Its unique properties also make it suitable for living hinge closure applications. This resin has been designed to meet demanding performance requirements, especially in the areas of environmental stress crack resistance, stiffness, impact strength, and sensory, while maintaining good processing characteristics beneficial to molders. Main Characteristics: Excellent ESCR, Stiffness, and Impact Strength Excellent Sensory Properties Excellent Processing Characteristics Complies with: U.S. FDA 21 CFR 177.1520(c)3.2a U.S. FDA-DMF Canadian HPFB No Objection Europe Commission Regulation (EU) No 10/2011 Consult the regulations for complete details.&&

About

CONTINUUM™ DMDC-1250 NT 7 High Density Polyethylene Resin (HDPE) is intended for use in both compression and injection molded closure applications including carbonated soft drink and hot fill closures. Its unique properties also make it suitable for living hinge closure applications. This resin has been designed to meet demanding performance requirements, especially in the areas of environmental stress crack resistance, stiffness, impact strength, and sensory, while maintaining good processing characteristics beneficial to molders. Main Characteristics: Excellent ESCR, Stiffness, and Impact Strength Excellent Sensory Properties Excellent Processing Characteristics Complies with: U.S. FDA 21 CFR 177.1520(c)3.2a U.S. FDA-DMF Canadian HPFB No Objection Europe Commission Regulation (EU) No 10/2011 Consult the regulations for complete details.&&

Product Description
Supplier	DOW
Generic	HDPE
Material Status	Commercial: Active
Availabilitys	North America,Latin America

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.955	g/cm³	ASTM D792
Melt Flow Rate
190℃，2.16kg	1.5	g/10min	ASTM D1238
ESCR(Environmental Stress Cracking Resistance)			ASTM D1693
50 ℃, 10% non-ionic surfactant, F50	272	hr	ASTM D1693
50 ℃, 100% non-ionic surfactant, F50	> 2000	hr	ASTM D1693

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
0.45 MPa, unannealed	68.3	℃	ASTM D648
Vicat Softening Temp	127	℃	ASTM D1525
Melting temperature
DSC	130	℃	Internal Method
Crystallization peak temperature
DSC	117	℃	Internal Method

MECHANICAL	Nominal value	Unit	Test method
Shore hardness
Shaw’s D	60		ASTM D2240
tensile strength			ASTM D638
yield	28.3	MPa	ASTM D638
fracture	22.1	MPa	ASTM D638
Tensile strain			ASTM D638
yield	9.0	%	ASTM D638
fracture	690	%	ASTM D638
Bending modulus
2% secant	1100	MPa	ASTM D790-B

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.