| About |
|---|
| tefabloc® TP SD 300 60A is a Thermoplastic Elastomer (TPE) material. It is available in Europe or North America for injection molding. Important attributes of tefabloc® TP SD 300 60A are: RoHS Compliant Chemical Resistant Food Contact Acceptable Good Aesthetics High Flow Typical applications include: Consumer Goods Outdoor Applications Sealing Applications Sporting Goods&& |
| Product Description | |
|---|---|
| Supplier | Mitsubishi |
| Generic | TPE |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Alkali resistant,Good surface appearance,High liquidity,Food contact compliance,Acidproof,Solvent resistance,Resistance to detergents |
| Availabilitys | North America,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.880 | g/cm³ | ISO 1183 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 57 | g/10min | ISO 1133 |
| Shrinkage rate | Internal Method | ||
| TD | 1.3 | % | Internal Method |
| MD | 1.2 | % | Internal Method |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore A, 15 seconds, injection molding | 60 | ISO 868 | |
| Abrasion | 230 | mm³ | DIN 53516 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| fracture | 3.40 | MPa | ISO 37 |
| 20% strain | 1.50 | MPa | ISO 37 |
| 100% strain | 2.30 | MPa | ISO 37 |
| Tensile strain | |||
| fracture | 670 | % | ISO 37 |
| tear strength | 24 | kN/m | ISO 34-1 |
| Compression deformation | ISO 815 | ||
| 23℃，22 hr | 22 | % | ISO 815 |
| 50℃，22 hr | 31 | % | ISO 815 |
| 50℃，22 hr | 43 | % | ISO 815 |
| 70℃，22 hr | 36 | % | ISO 815 |
| 70℃，22 hr | 52 | % | ISO 815 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Operating temperature | -50 to 70 | ℃ |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Resistance to Aging | 125 | ℃ |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| Color stability | ISO 105-A02 | ||
| — | 4/5 | ISO 105-A02 | |
| 100 hr | 5 | ISO 105-A02 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Barrel rear temperature | 160 | °C | |
| Barrel middle temperature | 170 | °C | |
| Barrel front temperature | 180 | °C | |
| Injection speed | Moderate | ||
| Screw compression ratio | 2.5:1.0 to 3.0:1.0 | ||
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Method Ba, Angle (Unnicked) |
| 3. Type B |
| 4. relaxation 50°C |
| 5. relaxation 23°C |
| 6. relaxation 70°C |
| 7. 1000 hr |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |