| About |
|---|
| Alcryn® 4660 NC is a Melt Processable Rubber (MPR) product. It can be processed by blow molding, calendering, compression molding, or extrusion and is available in Asia Pacific, Europe, or North America. Applications of Alcryn® 4660 NC include engineering/industrial parts, hose/tubing, wire & cable, fabrics/fibers and handles. Characteristics include: RoHS Compliant WEEE Compliant Chemical Resistant Heat Resistant UV Resistant&& |
| Product Description | |
|---|---|
| Supplier | A. Schulman |
| Generic | MPR |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,noise reduction,High Heat Resistance,Moderate liquidity,Grease resistance,Ozone resistance |
| Availabilitys | North America,Asia Pacific,Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 1.17 | g/cm³ | ASTM D792 |
| Density | 1.17 | g/cm³ | ISO 1183 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile permanent deformation | 7 | % | ASTM D412 |
| tear strength | |||
| 24℃ | 29.8 | kN/m | ASTM D624 |
| Compression deformation | ASTM D395B | ||
| 24℃，22 hr | 16 | % | ASTM D395B |
| 100℃，22 hr | 72 | % | ASTM D395B |
| Compression deformation | ISO 815 | ||
| 24℃，22 hr | 16 | % | ISO 815 |
| 100℃，22 hr | 72 | % | ISO 815 |
| Kappa’s modulus | |||
| -40℃ | 68.9 | MPa | ASTM D1043 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Embrittlement temperature | -68.9 | ℃ | ASTM D746 |
| Embrittlement temperature | -68.9 | ℃ | ISO 974 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change of Shore hardness in air | |||
| 125℃，168 hr | 54 | ISO 188 | |
| Change in Ultimate Elongation（125℃，168 hr） | 400 | % | ASTM D471 |
| Change in Durometer Hardness（125℃，168 hr） | 54 | ASTM D471 | |
| Volume change | ASTM D471 | ||
| 24℃，168 hr，in Reference Fuel B | 13 | % | ASTM D471 |
| 100℃，168 hr，in ASTM #1 Oil | -19 | % | ASTM D471 |
| 100℃，168 hr，in ASTM #3 Oil | 14 | % | ASTM D471 |
| 100 ℃, 168 hr, in water | 9.0 | % | ASTM D471 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shaw A, 1.91 mm, molded | 57 | ASTM D2240 | |
| Tensile modulus | |||
| 1.91 mm, molded into shape | 2.62 | MPa | ASTM D638 |
| 1.91 mm, molded into shape | 2.62 | MPa | ISO 527-2 |
| tensile strength | |||
| Yield, 1.91 mm, molded | 8.45 | MPa | ISO 527-2 |
| Yield, 1.91 mm, molded | 8.45 | MPa | ASTM D638 |
| Tensile strain | |||
| Fracture, 1.91 mm, molded | 440 | % | ASTM D638 |
| Fracture, 1.91 mm, molded | 440 | % | ISO 527-2 |
| Taber abraser | |||
| 1000 cycles, 1000 g, CS-17 wheels | 4.00 | mg | ASTM D1044 |
| IRHD hardness | 57 | ISO 48 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Processing (melt) temperature | 177 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |