Flexus 9212XP - SOLIAO

About
Braskem FLEXUS 9212XP is a linear low density polyethylene (LLDPE) produced through metallocene catalyst which presents excellent impact and puncture strength, beyond a differential sealing performance comparing with another typical LLDPE. It contains a special package of slip additives which allow better CoF control after lamination. Applications: Films laminated for automatic packaging (FFS) of solids and liquids, co extrusion and general use. Additive: Slip package in high level Blocking medium Processing Aids Medium Level Process: Blow Film Extrusion&&

About

Braskem FLEXUS 9212XP is a linear low density polyethylene (LLDPE) produced through metallocene catalyst which presents excellent impact and puncture strength, beyond a differential sealing performance comparing with another typical LLDPE. It contains a special package of slip additives which allow better CoF control after lamination. Applications: Films laminated for automatic packaging (FFS) of solids and liquids, co extrusion and general use. Additive: Slip package in high level Blocking medium Processing Aids Medium Level Process: Blow Film Extrusion&&

Product Description
Supplier	Braskem
Generic	Linear low density polyethylene
Material Status	Commercial: Active
Features	Excellent Processability,High impact resistance,Smoothness,Low density,Copolymer,Puncture Resistant,Hexene copolymers
Availabilitys	Latin America,Europe
Process Methods	Film extrusion

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	0.917	g/cm³	ASTM D792
Melt Flow Rate
190℃，2.16kg	1.0	g/10min	ASTM D1238

film	Nominal value	Unit	Test method
Secant modulus
1% secant, TD, 40 µ m, blow molded film	160	MPa	ASTM D882
1% secant, MD, 40 µ m, blow molded film	150	MPa	ASTM D882
tensile strength
TD, fracture, 40 µ m, blow molded film	25.0	MPa	ASTM D882
MD, fracture, 40 µ m, blow molded film	35.0	MPa	ASTM D882
Tensile strain
TD, fracture, 40 µ m, blow molded film	840	%	ASTM D882
MD, fracture, 40 µ m, blow molded film	850	%	ASTM D882
Drop hammer impact
40 µ m, blow molded film	700	g	ASTM D1709
tear strength
TD, 40 µ m, blow molded film	790	g	ASTM D1922
MD, 40 µ m, blow molded film	230	g	ASTM D1922

optical performance	Nominal value	Unit	Test method
gloss
60 °, 40.0 µ m, blow molded film	84		ASTM D2457
Haze
40 µ m, blow molded film	7.0	%	ASTM D1003

Notes
1. Typical properties: these are not to be construed as specifications.
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

1. Typical properties: these are not to be construed as specifications.

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.