| About |
|---|
| Product Description | |
|---|---|
| Supplier | Hyosung |
| Material Status | Commercial: Negative |
| Features | High Heat Resistance,Good flexibility,High modulus |
| Availabilitys | North America,Europe,Asia Pacific |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| MECHANICAL | Nominal value | Unit | Test method |
| tensile strength | |||
| yield | 140 | MPa | ASTM D638 |
| Tensile modulus | |||
| 7700 | MPa | ASTM D638 | |
| 7500 | MPa | ISO 527-1 | |
| elongation at break | 3.8 | % | ASTM D638 |
| bending strength | |||
| 190 | MPa | ASTM D790 | |
| 185 | MPa | ISO 178 | |
| Bending modulus | |||
| 6700 | MPa | ASTM D790 | |
| 6150 | MPa | ISO 178 | |
| Shore hardness | 83 | Shore D | ISO 868 |
| Rockwell hardness | 113 | R Scale | ASTM D785 |
| PHYSICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Density | 1.47 | g/cm³ | ASTM D792 |
| Water absorption rate | |||
| 50% RH | 0.4 | % | ASTM D570 |
| saturated | 1.7 | % | ASTM D570 |
| Melt index | |||
| 240℃，2.16kg | 14 | g/10min | ASTM D1238 |
| 240℃，2.16kg | 13 | g/10min | ISO 1133 |
| Mold shrinkage rate | |||
| MD, 3mm | 0.2 | % | ASTM D955 |
| TD, 3mm | 1.1 | % | ASTM D955 |
| MD, 2mm | 0.1 | % | ASTM D955 |
| TD, 2mm | 0.9 | % | ASTM D955 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Notched impact strength of cantilever beam | 104 | KJ/m² | ISO 180/1U |
| Impact strength of cantilever beam notch | 13 | KJ/m² | ISO 180/1A |
| Charpy Unnotch Impact strength | N.B | kJ/m² | ISO 179/1eU |
| Charpy Notched Impact Strength | 13 | kJ/m² | ISO 179/1eA |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Melting temperature | 222 | ℃ | ISO 11357 |
| Linear coefficient of thermal expansion | |||
| TD，25℃ – 55℃ | 9.7E-5 | ℃ | ASTM E831 |
| MD，25℃ – 55℃ | 2.8E-5 | ℃ | ASTM E831 |
| vicat softening point | |||
| 5kg | 210 | ℃ | ASTM D1525 |
| Hot deformation temperature | |||
| 0.45MPa | 215 | ℃ | ASTM D648 |
| 1.8MPa | 210 | ℃ | ASTM D648 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Dielectric strength | |||
| 3 mm | 17 | kV/mm | ASTM D149 |
| 2 mm | 22 | kV/mm | ASTM D149 |
| Volume resistivity | 10E+14 | ohm·cm | ASTM D257 |
| Surface resistivity | 10E+17 | ohm | ASTM D257 |
| Dielectric constant | |||
| 60Hz | 6.3 | ASTM D150 | |
| Dissipation factor | |||
| 60Hz | 0.011 | ASTM D150 |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |