| About |
|---|
| Telcar TL-90-T707E-100 BLK 111 is a high performance thermoplastic elastomer designed for electrical applications requiring flexibility over a wide temperature range. Telcar TL-90-T707E-100 BLK 111 is a high durometer grade that is UV stablized and contains anti-microbial additives. This grade is suitable for both injection molding and extrusion.&& |
| Product Description | |
|---|---|
| Supplier | Teknor Apex |
| Generic | TPE |
| Material Status | Commercial: Active |
| Features | Weather resistance is good,Good Hardness,Antimicrobial properties,Moderate liquidity,HB |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Extrusion |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.978 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 230℃，2.16kg | 7.0 | g/10min | ASTM D1238 |
| elastic body | Nominal value | Unit | Test method |
|---|---|---|---|
| tensile strength | |||
| fracture | 17.9 | MPa | ASTM D412 |
| 300% strain | 9.93 | MPa | ASTM D412 |
| 100% strain | 9.65 | MPa | ASTM D412 |
| Tensile strain | |||
| fracture | 580 | % | ASTM D412 |
| tear strength | |||
| 23℃ | 87.6 | kN/m | ASTM D624 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Shore hardness | |||
| Shore D, 1 second, injection molding | 42 | ASTM D2240 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Continuous use temperature | 105 | ℃ | ASTM D794 |
| Embrittlement temperature | -52.0 | ℃ | ASTM D746 |
| Vicat Softening Temp | 98.0 | ℃ | ASTM D1525 |
| Relative temperature index | |||
| Electrical performance | 50.0 | ℃ | UL 746 |
| Strength mechanical performance | 50.0 | ℃ | UL 746 |
| Aging performance | Nominal value | Unit | Test method |
|---|---|---|---|
| The rate of change in tensile strength in air | |||
| 136℃，168 hr | -5.0 | % | ASTM D573 |
| The rate of change in ultimate elongation in air | |||
| 136℃，168 hr | 1.0 | % | ASTM D573 |
| The rate of change in tensile strength | |||
| 60℃，168 hr，in IRM 902 Oil | -20 | % | ASTM D471 |
| Change in Ultimate Elongation（60℃，168 hr，in IRM 902 Oil） | -7.0 | % | ASTM D471 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | 1.0E+16 | ohms·cm | ASTM D257 |
| Dielectric strength | 38 | kV/mm | ASTM D149 |
| Dielectric constant | ASTM D150 | ||
| 23 ℃，1 kHz | 2.37 | ASTM D150 | |
| 23 ℃，1 MHz | 2.35 | ASTM D150 | |
| Dissipation factor | ASTM D150 | ||
| 23℃，1 kHz | 1.1E-3 | ASTM D150 | |
| 23℃，1 MHz | 8.6E-3 | ASTM D150 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| 1.50 mm, black | HB | UL 94 | |
| Extreme oxygen index | 19 | % | ASTM D2863 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Extrusion | Nominal value | Unit | Test method |
| Barrel rear temperature | 171 to 193 | °C | |
| Barrel middle temperature | 177 to 199 | °C | |
| Barrel front temperature | 182 to 204 | °C | |
| Nozzle temperature | 188 to 210 | °C | |
| Processing (melt) temperature | 188 to 210 | °C | |
| Mold temperature | 25 to 66 | °C | |
| Injection pressure | 1.38 to 6.89 | MPa | |
| Injection speed | Moderate-Fast | ||
| Back pressure | 0.172 to 0.345 | MPa | |
| Screw speed | 50 to 100 | rpm | |
| Cushion | 3.81 to 25.4 | mm | |
| Barrel 1 zone temperature | 166 to 188 | °C | |
| Barrel 2 zone temperature | 171 to 193 | °C | |
| Barrel 3 zone temperature | 177 to 199 | °C | |
| Barrel 4 zone temperature | 177 to 199 | °C | |
| Barrel 5 zone temperature | 182 to 204 | °C | |
| Nozzle temperature | 188 to 210 | °C | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Die C, 20 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |