| About |
|---|
| Borcom BG055AI is a polypropylene microcomposite intended for injection and back injection moulding. This material has an excellent balance between impact strength and stiffness, high melt flow rate and gives a good surface quality. Applications Borcom BG055AI is designed for: Air ducts Trunk claddings Climate control housings Special Features Long term high heat stabilised Excellent flowability UL registered under File E108112&& |
| Product Description | |
|---|---|
| Supplier | Borealis AG |
| Generic | PP not specified |
| Material Status | Commercial: Active |
| Features | Good Rigidity,Good surface appearance,High impact resistance,High liquidity,Heat Stabilized |
| Availabilitys | Africa & Middle East ,North America,Latin America,Asia Pacific,Europe |
| Process Methods | Injection Molding |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.920 | g/cm³ | ISO 1183 |
| Melt Flow Rate | ISO 1133 | ||
| 230℃，2.16kg | 22 | g/10min | ISO 1133 |
| 230℃，5.0kg | 96 | g/10min | ISO 1133 |
| Shrinkage rate | |||
| 2.0 mm | 1.5 | % | Internal Method |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Charpy Notched Impact Strength | ISO 179/1eA | ||
| -20℃ | 1.5 | kJ/m² | ISO 179/1eA |
| 23℃ | 3.5 | kJ/m² | ISO 179/1eA |
| Charpy Unnotch Impact strength | ISO 179/1eU | ||
| -20℃ | 30 | kJ/m² | ISO 179/1eU |
| 23℃ | 100 | kJ/m² | ISO 179/1eU |
| Impact strength of cantilever beam notch | ISO 180 | ||
| -20℃ | 1.5 | kJ/m² | ISO 180 |
| 23℃ | 3.5 | kJ/m² | ISO 180 |
| Notched impact strength of cantilever beam | ISO 180 | ||
| -20℃ | 18 | kJ/m² | ISO 180 |
| 23℃ | 60 | kJ/m² | ISO 180 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1.8 MPa, unannealed | 60.0 | ℃ | ISO 75-2/A |
| 0.45 MPa, unannealed | 108 | ℃ | ISO 75-2/B |
| Vicat Softening Temp | |||
| A50 | 156 | ℃ | ISO 306/A50 |
| B50 | 95.0 | ℃ | ISO 306 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| atomization | |||
| 16 hrs，100℃ | 1.1 | mg | DIN 75201 |
| Supplementary information | Nominal value | Unit | Test method |
|---|---|---|---|
| discharge | < 30.0 | µg/g | VDA 277 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | 2000 | MPa | ISO 527-1-2 |
| tensile strength | |||
| yield | 35.0 | MPa | ISO 527-2/50 |
| Bending modulus | 1850 | MPa | ISO 178 |
| bending strength | 45.0 | MPa | ISO 178 |
| Ball hardness | |||
| H358/30 | 90.0 | MPa | ISO 2039-1 |
| Process Conditions | |||
|---|---|---|---|
| injection | Nominal value | Unit | Test method |
| Hopper temperature | 40 to 80 | °C | |
| Processing (melt) temperature | 220 to 260 | °C | |
| Mold temperature | 30 to 50 | °C | |
| Hold pressure | 30.0 to 60.0 | MPa | |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. 0.079 in/min |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |