Durethan® DP 2131/20 H2.0 900051

About
Durethan® DP 2131/20 H2.0 900051 (干燥 ) PA 6, 20 % glass fibers, injection molding, heat-aging stabilized, improved surface finish, improved resistance to weathering&&Durethan® DP 2131/20 H2.0 900051 PA 6, 20 % glass fibers, injection molding, heat-aging stabilized, improved surface finish, improved resistance to weathering&&

Product Description
Supplier	LANXESS
Generic	PA6
Material Status	Commercial: Active
Features	Weather resistance is good,Good surface appearance,Heat Stabilized,HB
Availabilitys	Africa & Middle East ,North America,Latin America,Asia Pacific,Europe
Process Methods	Injection Molding

Technical Data
PHYSICAL	Nominal value	Unit	Test method
Density	1.28	g/cm³	ISO 1183
Apparent density	0.70	g/cm³	ISO 60
Shrinkage rate			ISO 2577
TD：280℃，2.0 mm	0.54	%	ISO 2577
TD：120℃，2.0 mm，4 hrs	0.19	%	ISO 2577
MD：280℃，2.0 mm	0.35	%	ISO 2577
MD：120℃，2.0 mm，4 hrs	0.12	%	ISO 2577

MECHANICAL	Nominal value	Unit	Test method
Tensile modulus
23℃	7600	MPa	ISO 527-1-2
tensile strength
Fracture, 23 ℃	150	MPa	ISO 527-2/5
Tensile strain
Fracture, 23 ℃	3.0	%	ISO 527-2/5
Bending modulus
23℃	6400	MPa	ISO 178-A
bending strength			ISO 178/A
3.50% strain, 23 ℃	200	MPa	ISO 178-A
23℃	225	MPa	ISO 178-A
Bending strain	4.5	%	ISO 178/A

IMPACT	Nominal value	Unit	Test method
Charpy Notched Impact Strength			ISO 179/1eA
-30℃	< 10	kJ/m²	ISO 179/1eA
23℃	< 10	kJ/m²	ISO 179/1eA
Charpy Unnotch Impact strength			ISO 179/1eU
-30℃	40	kJ/m²	ISO 179/1eU
23℃	45	kJ/m²	ISO 179/1eU
Impact strength of cantilever beam notch			ISO 180/1A
-30℃	< 10	kJ/m²	ISO 180-1A
23℃	< 10	kJ/m²	ISO 180-1A
Notched impact strength of cantilever beam			ISO 180/1U
-30℃	35	kJ/m²	ISO 180/1U
23℃	35	kJ/m²	ISO 180/1U
Multi axial instrumented impact energy			ISO 6603-2
-30℃	4.00	J	ISO 6603-2
23℃	5.00	J	ISO 6603-2

THERMAL	Nominal value	Unit	Test method
Hot deformation temperature
1.8 MPa, unannealed	215	℃	ISO 75-2/A
0.45 MPa, unannealed	213	℃	ISO 75-2/B
Vicat Softening Temp
B120	> 200	℃	ISO 306/B120
Melting temperature	222	℃	ISO 11357-3
Linear coefficient of thermal expansion
TD：23~55℃	8.9E-5	1/℃	ISO 11359-2
MD：23~55℃	2.3E-5	1/℃	ISO 11359-2

Electrical performance	Nominal value	Unit	Test method
Surface resistivity	2.0E+15	ohms	IEC 60093
Volume resistivity
23℃	3.0E+15	ohms·cm	IEC 60093
Relative permittivity			IEC 60250
23℃，100 Hz	4.10		IEC 60250
23℃，1 MHz	3.74		IEC 60250
Dissipation factor			IEC 60250
23℃，100 Hz	8.0E-3		IEC 60250
23℃，1 MHz	0.018		IEC 60250

FLAME CHARACTERISTICS	Nominal value	Test method
Flame retardant level		UL 94
0.80 mm	HB	UL 94
1.60 mm	HB	UL 94

Supplementary information	Nominal value	Unit	Test method
ISO Shortname	ISO 1874 PA 6, GHR, 14-080, GF20		ISO 1874

Process Conditions
injection	Nominal value	Unit	Test method
Drying Temperature – Dry Air Dryer	80	°C
Drying Time – Dry Air Dryer	2.0 to 6.0	hr
Processing (melt) temperature	270 to 290	°C
Mold temperature	80 to 120	°C
Residual Moisture Content	0.030 to 0.12	%

Notes
【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.

Notes

【 Disclaimer 】
Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials.