| About |
|---|
| ELITE™ 5940ST Polyethylene Resin is a copolymer produced via INSITE™ Technology from Dow. It offers a unique combination of excellent stiffness/toughness balance, good tear strength and an outstanding processability, allowing for the production of a variety of downgauged films at high output rates. Main Characteristics: Outstanding processability Excellent stiffness/toughness balance Complies with: U.S. FDA 21 CFR 177.1520 (c) 3.2a EU, No 10/2011 Consult the regulations for complete details.&& |
| Product Description | |
|---|---|
| Supplier | DOW |
| Generic | EPE |
| Material Status | Commercial: Active |
| Availabilitys | Europe |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| Density | 0.941 | g/cm³ | ASTM D792 |
| Melt Flow Rate | |||
| 190℃，2.16kg | 0.80 | g/10min | ASTM D1238 |
| film | Nominal value | Unit | Test method |
|---|---|---|---|
| film thickness | |||
| test | 51 | µm | |
| Secant modulus | ASTM D882 | ||
| 2% secant, MD: 51 µ m | 435 | MPa | ASTM D882 |
| 2% secant, TD: 51 µ m | 432 | MPa | ASTM D882 |
| tensile strength | ASTM D882 | ||
| MD, yield, 51 µ m | 19.4 | MPa | ASTM D882 |
| TD, yield, 51 µ m | 20.3 | MPa | ASTM D882 |
| MD, fracture, 51 µ m | 28.2 | MPa | ASTM D882 |
| TD, fracture, 51 µ m | 25.9 | MPa | ASTM D882 |
| Tensile strain | ASTM D882 | ||
| MD, fracture, 51 µ m | 540 | % | ASTM D882 |
| TD, fracture, 51 µ m | 600 | % | ASTM D882 |
| Drop hammer impact | |||
| 51 µm | 280 | g | ASTM D1709-A |
| Elmandorf tear strength | ASTM D1922 | ||
| MD：51 µm | 120 | g | ASTM D1922 |
| TD：51 µm | 570 | g | ASTM D1922 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Vicat Softening Temp | 123 | ℃ | ASTM D1525 |
| Melting temperature | |||
| DSC | 125 | ℃ | Internal Method |
| optical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| gloss | |||
| 45°，50.8 µm | 24 | ASTM D2457 | |
| Haze | |||
| 50.8 µm | 30 | % | ASTM D1003 |
| Notes |
|---|
| 1. Typical properties: these are not to be construed as specifications. |
| 2. Method B |
| 3. Method A |
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |