| About |
|---|
| Product Description | |
|---|---|
| Supplier | SUQING |
| Generic | Polyphenylene oxide + polystyrene blend |
| Material Status | Commercial: Negative |
| Features | Low density,Low or no water absorption,Good Dimensional Stability,High liquidity |
| Technical Data | |||
|---|---|---|---|
| PHYSICAL | Nominal value | Unit | Test method |
| proportion | |||
| 1.20 | g/cm³ | ISO 1183 | |
| 1.20 | g/cm³ | ASTM D 792 | |
| Shrinkage rate | |||
| flow | 0.5~0.7 | % | |
| vertical | 0.5~0.7 | % | |
| Water absorption rate | |||
| 23 ° C saturation | 0.2 | % | ISO 62 |
| 23°C 24hr | 0.1 | % | ISO 62 |
| 23 ° C 50RH balance | 0.05 | % | ISO 62 |
| 23°C 50RH 24hr | 0.02 | % | ISO 62 |
| 23 ° C saturation | 0.2 | % | ASTM D570 |
| 23°C 24hr | 0.1 | % | ASTM D570 |
| Melt index | |||
| 280℃10kg | 20 | cm³/10min | ISO 1133 |
| Rockwell hardness | |||
| M scale | 90 | ISO 2039 | |
| M scale | 90 | ASTM D785 | |
| Ball hardness | |||
| H358/30 | 214 | MPa | ISO 2039 |
| MECHANICAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Tensile modulus | |||
| 1.0mm/min | 4400 | MPa | ISO 527 |
| 5mm/min | 4200 | MPa | ASTM D638 |
| tensile strength | |||
| Fracture 5mm/min | 82 | MPa | ISO 527 |
| Fracture 5mm/min | 82 | MPa | ASTM D638 |
| elongation | |||
| Fracture 5mm/min | 2.5 | % | ISO 527 |
| Fracture 5mm/min | 2.5 | % | ASTM D638 |
| bending strength | |||
| 2.0mm/min | 132 | MPa | ISO 178 |
| 1.3mm/min | 132 | MPa | ASTM D790 |
| Bending modulus | |||
| 2.0mm/min | 4000 | MPa | ISO 178 |
| 1.3mm/min | 4000 | MPa | ASTM D790 |
| IMPACT | Nominal value | Unit | Test method |
|---|---|---|---|
| Impact strength of cantilever beam notch | |||
| 23°C 4.0mm | 6 | KJ/m² | ISO 180 |
| -30°C 40mm | 6 | KJ/m² | ISO 180 |
| 23°C | 70 | J/m | ASTM D256 |
| -30C | 60 | J/m | ASTM D256 |
| Notched impact strength of cantilever beam | |||
| 23°C 4.0mm | 25 | KJ/m² | ISO 180 |
| -30°C 40mm | 25 | KJ/m² | ISO 180 |
| 23°C | 440 | J/m | ASTM D4812 |
| -30C | 425 | J/m | ASTM D4812 |
| Charpy Notched Impact Strength | |||
| 23°C 4.0mm | 6 | kJ/m² | ISO 179 |
| 23°C 4.0mm | 6 | kJ/m² | ISO 179 |
| Charpy Unnotch Impact strength | |||
| 23°C 4.0mm | 25 | kJ/m² | ISO 179 |
| -30°C 40mm | 25 | kJ/m² | ISO 179 |
| Instrument shock | |||
| 23 ° C peak energy | 3 | J | ASTM D3763 |
| 23 ° C total energy | 4 | J | ASTM D3763 |
| 23 ° C peak force | 1340 | N | ASTM D3763 |
| THERMAL | Nominal value | Unit | Test method |
|---|---|---|---|
| Hot deformation temperature | |||
| 1. 8MPa 4. 0mm | 125 | ℃ | ISO 75 |
| 0.45MPa 4 0mm | 132 | ℃ | ISO 75 |
| Unannealed 1.8MPa 3.2mm | 127 | ℃ | ASTM D648 |
| Unannealed 0.45MPa 3.2mm | 134 | ℃ | ASTM D648 |
| Vicat Softening Temp | |||
| 50°C/hr 10N | 144 | ℃ | ISO 306 |
| 50°C/hr 50N | 136 | ℃ | ISO 306 |
| 120°C/hr 50N | 138 | ℃ | ISO 306 |
| 50°C/hr 10N | 144 | ℃ | ASTM D1525 |
| 50°C/hr 50N | 136 | ℃ | ASTM D1525 |
| 120°C/hr 50N | 138 | ℃ | ASTM D1525 |
| Linear expansion coefficient | |||
| Flowing -40 ° C to 40 ° C | 3.36E-5 | cm/cm/°C | ISO 11359 |
| Vertical -40.0~40 ° C | 5.83E-5 | cm/cm/°C | ISO 11359 |
| Flowing -40 ° C to 40 ° C | 3.36E-5 | cm/cm/°C | ASTM E831 |
| Vertical -40.0~40 ° C | 5.83E-5 | cm/cm/°C | ASTM E831 |
| Thermal conductivity coefficient | |||
| 0.21 | W/m/K | ISO 8032 | |
| 0.21 | W/m/K | ASTM D5930 | |
| Ball pressure test | 125 | ℃ | IEC 60695-10-2 |
| Electrical performance | Nominal value | Unit | Test method |
|---|---|---|---|
| Volume resistivity | |||
| 2.01E16 | ohms·cm | IEC 60093 | |
| 2.01E16 | ohms·cm | ASTM D257 | |
| Surface resistivity | |||
| 5.32E16 | ohms | IEC 60093 | |
| 5.32E16 | ohms | ASTM D257 | |
| Insulation strength | |||
| 0.80mm in oil | 51.7 | kV/mm | IEC 60243 |
| 3.2mm in oil | 21.7 | kV/mm | IEC 60243 |
| 1.6mm in air | 24.8 | kV/mm | IEC 60243 |
| 3.2mm in air | 15.3 | kV/mm | IEC 60243 |
| Dielectric constant | |||
| 50/60Hz | 3.37 | IEC 60250 | |
| 1MHz | 2.83 | IEC 60250 | |
| 50/60Hz | 3.37 | ASTM D150 | |
| 1MHz | 2.83 | ASTM D150 | |
| Dissipation factor | |||
| 50/60Hz | 0.1089 | IEC 60250 | |
| 1MHz | 0.0029 | IEC 60250 | |
| 50/60Hz | 0.1089 | ASTM D150 | |
| 1MHz | 0.0029 | ASTM D150 | |
| CTI | 250 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Nominal value | Unit | Test method |
|---|---|---|---|
| Flame retardant level | |||
| 1.5mm | v-0 | UL 94 | |
| 2.5mm | 5VB | UL 94 | |
| 2.5mm | 5VA | UL 94 | |
| 1.0mm | v-1 | UL 94 | |
| Igniting temperature of the hot wire | |||
| 1.5mm | 825 | ℃ | IEC 60695 |
| 3.0mm | 850 | ℃ | IEC 60695 |
| 1.0mm | 850 | ℃ | IEC 60695 |
| 2.0mm | 850 | ℃ | IEC 60695 |
| Relative temperature of heating wire | |||
| 1.5mm | 960 | ℃ | IEC 60695 |
| 3.0mm | 960 | ℃ | IEC 60695 |
| 2.0mm | 960 | ℃ | IEC 60695 |
| 1.0mm | 960 | ℃ | IEC 60695 |
| Process Conditions | |||
|---|---|---|---|
| injection molding | Nominal value | Unit | Test method |
| drying temperature | 105~110 | °C | |
| Drying time | |||
| 3~4 | hr | ||
| 8 | hr | ||
| Suggested moisture content | ≤0.02 | % | |
| First stage temperature | 250~300 | °C | |
| Second stage temperature | 260~305 | °C | |
| Third stage temperature | 270~310 | °C | |
| Nozzle temperature | 280~310 | °C | |
| Melting temperature | 280~310 | °C | |
| Mold temperature | 75~105 | °C | |
| Screw speed | 20~100 | rpm | |
| Recommended injection volume | 30~70 | % | |
| Back pressure | 0.3~0.7 | MPa | |
| Notes |
|---|
| 【 Disclaimer 】 Guangzhou Soliao Information Technology Co., Ltd. reserves all rights. The information in this data table was obtained from the manufacturer of the material on soliao.com. Soliao.com makes every effort to ensure the accuracy of this data. However, the search company does not assume any responsibility for the uncertainty and consequences caused to users by these data values and suggestions, and strongly recommends verifying the data values with the material supplier before the final selection of materials. |